提高转炉上连铸Q345B探伤质量的措施

doi:10.13228/j.boyuan.issn1005-4006.20200056

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (1952 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要针对南阳汉冶特钢有限公司250 mm×1 650 mm断面采取转炉直上连铸工艺路线生产的Q345B钢板探伤合格率低现象,对不合格钢板取样并进行电镜检测分析,得出中心锰偏析、硫化锰夹杂是导致探伤不合格的主要原因。通过优化转炉脱硫工艺降低硫含量、严控钢水过热度、优化成分降低锰含量、优化连铸二冷制度、钢板抢温下线缓冷等措施,铸坯中心偏析得到了改善,轧后钢板探伤质量合格率得到了提高。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	作者相关文章
	赵迪
	石教兴
	李红洋
	程业
	李博

关键词 ：钢板, 探伤, 电镜, 偏析, 夹杂

Abstract：According to the phenomenon that the qualified rate of Q345B steel plate produced by the process of converter straight up continuous casting on 250 mm×1 650 mm section of Nanyang Hanye Special Steel Co., Ltd. unqualified steel plate was sampled and analyzed by electron microscope. It is concluded that the main reasons for unqualified inspection are the central manganese segregation and the manganese sulfide inclusion. By optimizing the desulfurization process of converter to reduce sulfur content, strictly controlling the superheat of molten steel, optimizing the composition to reduce manganese content, optimizing the secondary cooling system of continuous casting and slow cooling of steel plate, central segregation of slab has been improved, and qualified rate of steel plate flaw detection has been improved after rolling.

Key words： steel plate flaw detection electron microscopy segregation inclusion

收稿日期: 2020-04-20

引用本文:

赵迪, 石教兴, 李红洋, 程业, 李博. 提高转炉上连铸Q345B探伤质量的措施[J]. 连铸, 2020, 39(4): 34-39. ZHAO Di, SHI Jiao-xing, LI Hong-yang, CHENG Ye, LI Bo. Measures to improve flaw detection quality of Q345B continuous casting on converter. CONTINUOUS CASTING, 2020, 39(4): 34-39.

链接本文:

http://www.chinamet.cn/Jweb_lz/CN/10.13228/j.boyuan.issn1005-4006.20200056 或 http://www.chinamet.cn/Jweb_lz/CN/Y2020/V39/I4/34

[1]	周彦召,邹长东. 100 t钢包精炼渣系优化选择及应用[J].炼钢,2018,34(4):12.
[2]	黄永生,孙光涛,顾超,等. 铝脱氧轴承钢GCr15精炼渣最优成分的分析与实践[J].中国冶金,2017,27(12):44.
[3]	赵沛,成国光,沈甦.炉外精炼及铁水预处理实用技术手册[M]. 北京:冶金工业出版社,2004:265.
[4]	谭清元,周远华,贾至立,等. Q345R钢板超声波探伤不合的原因分析[J].钢铁,2011,46(3):66.
[5]	许少普,崔冠军,刘庆波,等. 中厚板超声波探伤合格率提高攻关实践[J].钢铁,2011,46(3):92.
[6]	崔冠军,许少普,刘庆波,等. 提高20～60 mm规格Q345B钢板探伤合格率的攻关实践[J].中国冶金,2010,20(7):26.
[7]	黄星武. Q345D风电钢探伤不合格原因分析[J].钢铁研究,2017,45(6):98.
[8]	董鹏莉,尚海霞,王华. 铸坯及板卷典型质量缺陷成因与控制技术[J].中国冶金,2017,27(6):7.
[9]	蔡开科. 铸坯质量(第六讲)——连铸坯偏析控制[J].连铸,1994,19(6):39.
[10]	余宏伟,程吉浩,董中波,等. 厚规格高性能500 MPa结构钢探伤不合格原因分析[J].钢铁研究,2017,45(2):59.
[11]	朱苗勇.现代冶金工艺学[M]. 北京:冶金工业出版社,2014:188.
[12]	赵中福,赵继宇,李小明,等. 100 t LF精炼脱硫生产实践[J].中国冶金,2009,19(4):18.
[13]	薛正良,胡志刚,阎小平,等. 弱脱氧钢水脱硫工艺研究[J].钢铁,2008,43(6):22.
[14]	张雪亚,杨宗月,刘阳,等. 化学元素对钢的力学性能的影响[J].矿产综合利用,2018(5):147.