IF钢板坯表层大尺寸夹杂物的三维分布

doi:10.13228/j.boyuan.issn1005-4006.20220015

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (4435 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要 IF钢铸坯表层大尺寸夹杂物分布对冷轧钢板表面质量有较大影响。采用ASPEX自动检测法与逐层刨削法研究了IF钢铸坯表层20 mm内中100 μm以上夹杂物的三维分布。铸坯表层20 mm内夹杂物共分成3类,气泡、氧化铝+气泡、块状氧化铝,数量比例分别为72%、26%和2%。结合水模型研究了结晶器内大尺寸夹杂物被凝固坯壳捕获行为,结果表明,在现有浇铸工况下结晶器内大尺寸夹杂物主要集中在上回流涡心处与浸入式水口下部等结晶器“死区”位置。消除结晶器内死区有助于减少铸坯表层大尺寸夹杂物,提高轧板表面质量。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	作者相关文章
	邓小旋
	李海波
	季晨曦
	陈斌
	朱国森

关键词 ： IF钢, 铸坯, 大尺寸夹杂物, 上回流, 死区

Abstract：The distributions of macro-inclusions plays an significant role in surface quality of cold rolled steel sheets. The three-dimensional distribution of inclusions over 100 μm in 20 mm surface of IF steel slab was studied by ASPEX automatic detection method and layer-by-layer planing method.It is found that three kinds of macro inclusions were detected, bubbles, alumina plus bubbles and brick alumina and their number percentage occupy 72%、26% and 2%,respectively. The large sized macro inclusions mainly concentrated within the upper roll center zone and stagnant zone below the submerged entry nozzle (SEN) bottom according to the full scale water modeling of mold domain. Eliminating the dead zone in mold is helpful to reduce the large size inclusions and improve the surface quality of rolled products.

Key words： IF steel slab macro inclusion upper roll flow dead zone

收稿日期: 2022-01-31

引用本文:

邓小旋, 李海波, 季晨曦, 陈斌, 朱国森. IF钢板坯表层大尺寸夹杂物的三维分布[J]. 连铸, 2022, 41(2): 35-40. DENG Xiao-xuan, LI Hai-bo, JI Chen-xi, CHEN Bin, ZHU Guo-sen. Three-dimensional distribution on macro inclusions in surface layer of IF steel slabs. CONTINUOUS CASTING, 2022, 41(2): 35-40.

链接本文:

http://www.chinamet.cn/Jweb_lz/CN/10.13228/j.boyuan.issn1005-4006.20220015 或 http://www.chinamet.cn/Jweb_lz/CN/Y2022/V41/I2/35

[1]	于会香, 潘明,杨德新.超低碳IF钢脱氧合金化过程中夹杂物的行为[J].钢铁,2020, 55 (6): 46.
[2]	徐国军, 胡华东, 田川,等. Al2O3夹杂在DC06钢中的分布及对深冲性能的影响[J].中国冶金,2021, 31 (5): 111.
[3]	上官方钦, 刘正东, 殷瑞钰.钢铁行业“碳达峰”“碳中和”实施路径研究[J].中国冶金,2021, 31 (9): 15.
[4]	上官方钦, 周继程, 王海风,等. 气候变化与钢铁工业脱碳化发展[J].钢铁,2021, 56 (5): 1.
[5]	马文俊, 李海波, 刘国梁,等.高等级汽车板中间包冶金技术[J].连铸,2021 (5): 99.
[6]	邓小旋, 季晨曦, 王胜东, 等. 冷轧薄板线状缺陷的工艺控制[J].中国冶金,2017, 27 (4): 55.
[7]	朱国森, 季晨曦, 刘洋,等.首钢板坯连铸技术进步[J].中国冶金,2019, 29 (8): 1.
[8]	Zhang L,Thomas B G. State of the art in evaluation and control of steel cleanliness[J].ISIJ International,2003, 43 (3): 271.
[9]	Jacobi H,Wunnenberg K.Improving oxide cleanness on basis of MIDAS method[J].Ironmaking and Steelmaking,2003, 30 (2): 130.
[10]	刘新华, 蔡开科, 王兰香,等. 超低头连铸板坯非金属夹杂物研究[J].钢铁,1991, 26 (9): 25.
[11]	Awajiya Y, Kubota Y,Takeuchi S. Inclusion entrapment location in solidified shell of ultra low carbon steel slab[C]//AISTech Proceedings.USA: Association for Iron and Steel Technology, 2005:65.
[12]	ZHANG Q, WANG L,WANG X. Influence of casting speed variation during unsteady continuous casting on non-metallic inclusions in IF steel slabs[J].ISIJ International,2006, 46 (10): 1421.
[13]	雷勋惠, 张立峰, 杨文, 等. X射线断层扫描技术在铸坯质量检测上的应用[J].中国冶金,2020, 30 (12): 44.
[14]	DENG X, JI C, ZHU G, et al.Quantitative evaluations of surface cleanliness in IF steel slabs at unsteady casting[J].Metallurgical and Materials Transactions B,2019, 50(4): 1974.
[15]	DENG X, JI C,CUI Y, et al. Formation and evolution of macro inclusions in IF steels during continuous casting[J].Ironmaking and Steelmaking,2017, 44 (10): 739.
[16]	高帅, 王敏, 郭建龙: IF钢铸坯厚度方向夹杂物分布及洁净度评估[J].工程科学学报,2020, 42 (2): 194.
[17]	Marukawa K. The challenge of braking the limit of the steel refining on the mass production[C]//19th Steelmaking Commission Reaction Process Research. Japan:Japan Society for the Promotion of Science,1996:1.
[18]	Tsai H T, Sammon W J, Hazelton D E. Characterization and countermeasures for sliver defects in cold rolled products[C]//Steelmaking Conference Proceedings. Detroit: Iron and Steel Society, 1990:49.
[19]	LIU Z, LI B, WU M,et al. An experimental benchmark of non-metallic inclusion distribution inside a heavy continuous-casting slab[J].Metallurgicaland Materials Transactions A,2019, 50 (3): 1370.
[20]	邓小旋, 潘宏伟, 季晨曦, 等.常规低碳钢板坯的高速连铸工艺技术[J].钢铁,2019, 54 (8): 70.
[21]	杨志刚, 徐子谦, 黄伟丽, 等. 连铸板坯角部纵裂原因分析及控制措施[J]. 连铸, 2021(6): 71.
[22]	冯永平, 郑娜, 唐磊, 等. 薄板坯连铸结晶器内钢水凝固传热数值模拟[J]. 连铸, 2021(6): 44.
[23]	王章印, 姜敏, 王新华. Q345D钢精炼过程夹杂物生成及演变行为[J]. 钢铁, 2022, 57(2): 63.
[24]	杨健, 蔡文菁. 镁处理对钢中夹杂物以及HAZ组织和性能的影响[J]. 钢铁, 2021, 56(7): 13.
[25]	DENG X, JI C, CUI Y,et al. Flow pattern control in continuous slab casting moulds:Physical modelling and plant trials[J].Ironmaking and Steelmaking,2017, 44 (6): 461.