水口结构对板坯结晶器液面流动行为的影响

doi:10.13228/j.boyuan.issn1005-4006.20210122

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (0 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Aiming at the phenomena of mold powder involvement and warping defects in the surface of stainless steel strip products, the correlation between the flow behavior of molten steel in the continuous casting mold and the involved process parameters of submerged entry nozzle was experimentally studied based on the actual production conditions. A water model of geometrical ratio 0.65∶1 was set up based on similarity principle, and the hydrodynamic behavior of mold liquid level under different submerged entry nozzle structures and casting process parameters was evaluated and optimized. The effects of casting speed, nozzle immersion depth, side port upward angle (4°, 8°, 15°) and nozzle port shape (rectangular and inverted trapezoid) on the mold level fluctuation and surface velocity were studied experimentally. The results show that the influence of casting speed and immersion depth on liquid level fluctuation is greater than that of nozzle structure. The increase in casting speed and the decrease in nozzle immersion depth aggravate the fluctuation of liquid level in the mold obviously. With the nozzle upward angle increasing from 4° to 8° and 15°, the flow velocity on the mold surface tends to drop, and the jet flow impact depth decreases, which results in an increasing mold level fluctuation at the meniscus. It has been revealed that the appropriate nozzle structure is an inverted trapezoidal one with upward angle of 8°. At casting speed of 1.10 m/min and nozzle immersion depth of 110-120 mm with the recommended nozzle, its measured wave height of mold liquid level is 1.1-1.2 mm and the average surface velocity is around 0.103 m/s. Meanwhile, the optimized scheme is compared with the original scheme by numerical simulation, showing that the liquid level of the optimized scheme is relatively stable and the probability of the shearing slag entrapment is low.

Key words： slab mold physical modelling submerged entry nozzle level fluctuation free surface velocity numerical simulation

Received: 13 October 2021

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LIU Yan-bin
	TANG Hai-yan
	WANG Kai-min
	MA Yu
	SHANG Guang-hao
	ZHANG Li-ping
	ZHANG Jia-quan

Cite this article:

LIU Yan-bin,TANG Hai-yan,WANG Kai-min等. Effect of submerged entry nozzle structures on liquid surface flow behavior of slab continuous casting mold[J]. CONTINUOUS CASTING, 2022, 41(3): 1-10.

URL:

http://www.chinamet.cn/Jweb_lz/EN/10.13228/j.boyuan.issn1005-4006.20210122 OR http://www.chinamet.cn/Jweb_lz/EN/Y2022/V41/I3/1

[1]	王博,吴晓燕,朱立光,等. 连铸坯表层夹杂轧制过程演变行为[J]. 中国冶金, 2019, 29(3): 5.
[2]	苑鹏,李海波,陈斌,等. 汽车钢板表面线状缺陷控制技术[J]. 钢铁研究学报, 2017, 29(10): 800.
[3]	Cho S M, Thomas B G, Kim S H. Effect of nozzle port angle on transient flow and surface slag behavior during continuous steel slab casting[J]. Metallurgical and Materials Transactions B, 2019, 50(1): 52.
[4]	Wang Z, Mukai K, Ma Z, et al. Influence of injected Ar gas on the involvement of the mold powder under different wettabilities between porous refractory and molten steel[J]. ISIJ International, 1999, 39(8): 795.
[5]	李晓军, 陈景锋, 马骏鹏, 等. 浸入式水口结构对409L钢连铸坯表面“卷渣”的影响[J]. 特殊钢, 2020, 41(3): 1.
[6]	金友林, 包燕平, 刘建华, 等. 不锈钢板坯连铸结晶器内钢/渣界面行为模拟及卷渣分析[J]. 北京科技大学学报, 2009, 31(5): 618.
[7]	吴颖东,刘中秋,全明杰,等. 连铸结晶器内钢/渣界面波动及卷渣行为的实验研究[J]. 材料与冶金学报, 2020, 19(1): 13.
[8]	陈景锋. 宽幅不锈钢连铸工艺的控制与优化[D]. 武汉:武汉科技大学, 2018.
[9]	刘纲,干勇,刘崇,等.超低碳IF钢边部翘皮缺陷改善及控制探究[J].连铸,2020(2):52.
[10]	邓小旋, 熊霄, 王新华, 等. 高拉速板坯连铸结晶器浸入式水口的水模型研究[J]. 北京科技大学学报, 2013, 35(10): 1304.
[11]	张开天, 刘建华, 崔衡, 等. 浸入式水口对结晶器钢水流动与液面波动的影响[J]. 工程科学学报, 2018, 40(6): 697.
[12]	赵洪强, 王叶婷, 国兴龙, 等. 水口侧孔角度对不锈钢板坯连铸结晶器内流场和温度场的影响[J]. 连铸, 2011(增刊1): 81.
[13]	王承顺, 李六一, 成国光, 等. 304不锈钢板坯浸入式水口形状对铸坯凝固组织的影响[J]. 连铸, 2017 (6): 26.
[14]	邓南阳, 金友林. 304不锈钢板坯连铸结晶器水口结构优化的数值模拟[J]. 特殊钢, 2010, 31(3): 10.
[15]	蒋鹏,何文远,乔焕山,等. 汽车外板连铸结晶器流场与SEN出口形状优化[J]. 炼钢, 2020, 36(1): 34.
[16]	ZHANG T, YANG J, XU G J, et al. Effects of operating parameters on the flow field in slab continuous casting molds with narrow widths[J]. International Journal of Minerals, Metallurgy and Materials, 2021, 28(2): 238.
[17]	胡群, 张硕, 王璞, 等. 大方坯结晶器内液面波动与卷渣行为[J]. 中国冶金, 2020, 30(6): 63.
[18]	王永胜, 王新华, 王万军. 板坯连铸结晶器流场及液面波动水模研究[J]. 连铸, 2009(6): 13.
[19]	张宁, 雷洪, 刘承军, 等. 连铸结晶器内液面波动及卷渣行为的物理模型研究[J]. 连铸, 2010(1): 30.
[20]	曹娜,朱苗勇. 高拉速板坯连铸结晶器内钢/渣界面行为的数值模拟[J]. 金属学报, 2007, (8): 834.
[21]	Miranda R, Barron M A, Barreto J, et al. Experimental and numerical analysis of the free surface in a water model of a slab continuous casting mold[J]. ISIJ International, 2005, 45(11): 1626.
[22]	邱春根, 时朋召, 徐李军, 等. 250 mm×1800 mm板坯连铸结晶器浸入式水口优化的物理模拟[J]. 特殊钢, 2017, 38(2): 11.
[23]	马超,何文远,乔焕山,等. 水口倾角大范围变化对宽板坯连铸结晶器流场的影响[J]. 炼钢, 2021, 37(4): 16.