挡墙设计对四流T型中间包钢液流动行为的影响

doi:10.13228/j.boyuan.issn1005-4006.20210115

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (0 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The design of retaining wall plays an important role in fluid control of T-type tundish. In this paper, the influence of retaining walls with different diversion holes on the mixing of molten steel and the consistency of each outlet in a four-strand tundish of a steelmaking plant were studied by using the experimental method of “stimulus-response” hydraulic simulation. The results show that the ratio of dead zone is at a relatively low level under the prototype tundish, and there is a big difference between the response time of far outlet and near outlet, and the flow pattern of liquid steel will deteriorate with the increase of flow rate. By reducing the diameter of the diversion hole and designing an upward angle of 45°, the optimized scheme produces a large circulation structure inside the tundish and prolongates the response time of the near flow outlet, which brings forth the increase of plug volume from 6.61% to 9.04%. The consistency index of each outflow is reduced from 22.8 to 9.6 by 58%, and the dead zone ratio is slightly reduced, which is conducive to improving the overall metallurgical performance of the tundish.

Key words： T-type tundish retaining wall diversion hole physical simulation consistency

Received: 03 October 2021

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	GAO Jiang
	LIU Qing
	LI Quan-hui
	SUN Jian-kun
	TAO Biao
	ZHANG Jiang-shan

Cite this article:

GAO Jiang,LIU Qing,LI Quan-hui等. Effect of wall design on fluid flow inside a four-strand T-type tundish[J]. CONTINUOUS CASTING, 2022, 41(3): 11-17.

URL:

http://www.chinamet.cn/Jweb_lz/EN/10.13228/j.boyuan.issn1005-4006.20210115 OR http://www.chinamet.cn/Jweb_lz/EN/Y2022/V41/I3/11

[1]	Sahai Y, Emi T, 朱苗勇.洁净钢生产的中间包技术[M].北京:冶金工业出版社, 2009.
[2]	Sahai Y, Tundish technology for casting clean steel: A review[J]. Metallurgical and Materials Transactions B, 2016, 47(4):2095.
[3]	Mazumdar D. Review analysis and modeling of continuous casting tundish systems[J]. Steel Res Int, 2019, 90:1800279.
[4]	常朋飞,俞学成,孙亮,等.板坯连铸机全保护浇注工艺优化[J].河北冶金,2021(12):51.
[5]	袁己百,马志民,殷攀,等.四流H型感应加热中间包控流装置设计[J].连铸,2021(6):85.
[6]	包燕平,王敏.中间包冶金技术发展趋势[J].连铸,2021(5):2.
[7]	刘逸波,杨健.中间包流场控制技术的进展[J].连铸,2021(5):12.
[8]	李永祥,程乃良,陈志平,等.三流Τ型中间包内控流装置优化的物理模拟[J]. 中国冶金,2008,18(2): 29.
[9]	翟晓毅,颜慧成,杨海滨,等.八流中间包结构优化水模型试验研究[J].炼钢, 2018,34(1): 25.
[10]	刘艳贺,贺铸,刘双,等.二流T型23 t中间包控流装置的数值模拟和结构优化[J].特殊钢,2013,34(5):5.
[11]	储成阳,徐宇,武鸿杰,等.五流中间包稳态及非稳态试验[J].连铸, 2020 (5):7.
[12]	王伟,朱立光,张彩军. 双流T-型中间包的流场模拟及其控流结构优化[J], 连铸, 2020(2):62.
[13]	茅晓慧,李京社,张江山,等.特殊非对称型12流35 t中间包的水模拟试验和控流装置的优化[J].特殊钢,2014,35(2):1.
[14]	陈希青,肖红,王璞,等.双通道感应加热中间包的三维磁流热耦合模型[J].钢铁,2021,56(6):48.
[15]	马钰,唐海燕,张硕,等.通道式感应加热五流中间包流场的水力学模拟[J].钢铁,2020,55(11):57.
[16]	朱坦华,周秋月,任英,等.二次氧化过程IF钢中间包中夹杂物演变行为[J].钢铁,2020,55(3):35.
[17]	郭磊. 四流T型中间包内流体流场物理模拟的研究[J]. 工业加热,2013, 42(4):22.
[18]	俞占扬,刘坤,颜慧成,等. 改善六流中间包内流体流动特性的研究铸造技术[J]. 2017,38(5):1130.
[19]	张莉,李京社,张江山,等. 四流T型中间包控流装置优化的水模拟分析[J]. 重庆大学学报. 2015,38(5):119.
[20]	李少翔,铁占鹏,郑宝安,等. 三流大方坯连铸中间包流场优化数值模拟研究[J].连铸. 2019(5):47.
[21]	FANG Q, ZHANG H, LUO R, et al. Optimization of flow heat transfer and inclusion removal behaviors in an odd multi-strand bloom casting tundish[J]. Journal of Materials Research and Technology, 2020, 9(1):347.
[22]	雷洪,赵岩,鲍家琳,等.多流连铸中间包停留时间分布曲线总体分析方法[J]. 金属学报,2010, 46(9) : 1109.
[23]	杨树峰,吴金强,李京社,等.四流中间包控流装置优化物理模拟[J].中国冶金, 2019, 29(4):81.