Q355B板坯连铸凝固传热行为数值模拟

doi:10.13228/j.boyuan.issn1005-4006.20220122

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (3849 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract In order to solve the problem that the continuous casting parameters of Q355B slab in a steel plant do not match with each other when the casting speed is increased, ProCAST software was employed to establish the solidification heat transfer model of the slab, and the solidification characteristics of the slab under different continuous casting parameters were studied. The results show that the casting speed has the greatest influence on the slab solidification, followed by the specific water flow rate, and the smallest is superheat in the calculated range. With the increase of casting speed or the decrease of specific water rate or the increase of superheat, the slab temperature, the solidification end and the length of two-phase zone increase to different degrees except the shell thickness. In the actual production process,it is found that changing the casting speed billet production without changing the specific water volume and the position under light pressure, the three failed to effectively cooperate with each other, resulting in serious intermediate cracks. Based on simulation results, when the casting speed is increased to 1.0 m/min, the specific water flow rate is increased from 0.38 L/kg to 0.55 L/kg, as a result, the generation ratio of intermediate crack is reduced from 70% to about 11%, and the center segregation of slab above the level of C1.5 increases by 24.5%.

Key words： Q355B slab continuous casting solidification and heat transfer numerical simulation intermediate crack

Received: 18 July 2022

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	ZHOU Guo-tao
	CHEN Jin
	HUANG Biao-cai
	YAN Wei
	LI Jing

Cite this article:

ZHOU Guo-tao,CHEN Jin,HUANG Biao-cai等. Numerical simulation of solidification and heat transfer of Q355B slab during continuous casting[J]. CONTINUOUS CASTING, 2023, 42(2): 43-51.

URL:

http://www.chinamet.cn/Jweb_lz/EN/10.13228/j.boyuan.issn1005-4006.20220122 OR http://www.chinamet.cn/Jweb_lz/EN/Y2023/V42/I2/43

[1]	张成元,郑林. 连铸技术的发展与思考[J]. 江苏冶金,2007(2):5.
[2]	袁志鹏, 朱立光, 韩毅华, 等. 碱度对高速薄板坯保护渣结晶性能的影响[J]. 中国冶金, 2023, 33(1): 47.
[3]	王海风, 平晓东, 周继程, 等. 中国钢铁工业绿色发展回顾及展望[J]. 钢铁, 2023, 58(2): 8.
[4]	刘坤龙,吕明,宋保民,等.Q355B铝镇静钢夹杂物演变及钙处理工艺优化[J].钢铁,2022,57(12):79.
[5]	马永福,胥明旺,叶高旗,等.加热工艺窄范围控制对Q355B/C铸坯原始奥氏体晶粒度的影响[J].河北冶金,2022(5):13.
[6]	陈建超,庞洪轩,温超,等.终轧温度对加Ti低合金Q355B钢板组织性能的影响[J].中国冶金,2021,31(10):30.
[7]	蔡开科. 连铸坯裂纹控制[C]//板坯连铸技术研讨会论文汇编.济南:中国金属学会,2003:5.
[8]	张创举, 申文君, 潘时松, 等. Q355热轧板山峰状表面裂纹形貌特征和形成原因[J]. 中国冶金, 2023, 33(1): 55.
[9]	杨志刚,黄伟丽,王信威,等.低碳钢连铸板坯角部横裂的控制[J].河北冶金,2022(7):44.
[10]	韩志强,蔡开科. 微观偏析模型在碳钢内裂纹敏感性分析中应用[J]. 北京科技大学学报,2000,22(5):442.
[11]	赵杨.中高碳钢连铸板坯中心偏析的控制[J].河北冶金,2021(8):47.
[12]	祁猛,李亮,铁占鹏,等. 轻压下对GCr15轴承钢大方坯内部质量的影响[J]. 中国冶金,2020,30(9):67.
[13]	马建超,桂仲林,苏笃星,等. Q345B厚板坯连铸轻压下工艺的优化[J]. 钢铁,2012,47(4):38.
[14]	WANG B, ZHANG J, XIAO C, et al. Analysis of internal cracks in continuous casting slabs with soft reduction[J]. High Temperature Materials and Processes,2016,35(3):269.
[15]	元鹏飞,蒋朝晖,赵海明. Q345B中厚板连铸坯中间裂纹成因分析及控制[J]. 连铸,2021(4):38.
[16]	兰鹏,韩庚维,李亮,等. 直上钢Q235B板坯高拉速下中间裂纹的形成与调控[J]. 钢铁,2019,54(8):144.
[17]	王国连,曹磊. 宽厚板连铸坯中间裂纹成因分析及控制[J]. 中国冶金,2017,27(10):54.
[18]	吴晨辉,李阳,谢鑫,等. 板坯连铸过程凝固传热数值计算与工艺优化[J]. 中国冶金,2022,32(3):92
[19]	任廷志,李岩,马财生,等. 板坯连铸凝固传热数学模型的研究与开发[J]. 铸造技术,2016,37(4):723
[20]	高向宙,杨树峰,李京社,等. 宽厚板坯连铸凝固过程数值模拟[J]. 铸造技术,2015,36(3):678.
[21]	TIEU A K, KIM I S. Simulation of the continuous casting process by a mathematical model[J]. International Journal of Mechanical Sciences,1997,39(2):185.
[22]	LONG M, CHEN D. Study on mitigating center macro-segregation during steel continuous casting[J]. Steel Res Int, 2011, 82(7):847.
[23]	潘文峰,蔡兆镇,王少波,等. 连铸板坯二冷高温区传热均匀性研究与优化[J]. 中国冶金,2021,31(8):23.
[24]	肖红,王璞,郑晴,等.辊式电磁搅拌线圈位置对板坯凝固行为的影响[J].钢铁,2023,58(3):79.
[25]	仲红刚,王人杰,翟启杰.冶金凝固过程试验研究方法及应用[J].钢铁,2022,57(10):19.
[26]	孔谦祥. 有限单元法在传热学中的运用[M]. 北京:北京科学出版社,1996.
[27]	康丽,王恩刚,赫冀成. 连铸结晶器温度场及热变形的数值模拟[J]. 材料与冶金学报,2006(3):190.
[28]	纪元. 连铸还偏析及其铸轧遗传性研究[D]. 北京:北京科技大学,2018.
[29]	宋伟. 中厚板坯连铸冷却凝固过程数值模拟[D]. 安徽:安徽工业大学,2014.
[30]	陈洪智,常运合,张家泉,等. 不锈钢板坯连铸自由线收缩与辊缝研究[J]. 中国冶金,2012,22(2):25.
[31]	RAPPAZ M, GANDIN C A. Probabilistic modelling of microstructure formation in solidification processes[J]. Acta Metallurgica et Materialia,1993,41(2):345.
[32]	王璐,孙彦辉,牛阿朋,等. X80板坯传热凝固数值模拟[J]. 钢铁钒钛,2018,39(6):143.
[33]	庄清云. 板坯连铸凝固传热和轻压下工艺的研究[D].沈阳:东北大学,2013.
[34]	MASAHITO H, MASAYUKI K, AKIHIRO Y. Growth of solidified shell just below the meniscus in continuous casting mold[J]. ISIJ International,2009,49(3):365.
[35]	陈素琼,崔立新,张家泉,等. 浅析凝固末端轻压下技术在板坯连铸机上的实时控制[C]//2002年全国(第五届)炼钢、连铸和轧钢自动化学术会议论文集.北京:中国金属学会,2002.
[36]	YIM C, PARK J, YOU B, et al. The effect of soft reduction on center segregation in CC Slab[J]. ISIJ International,2007,36(S1):231.
[37]	OGIBAYASHI S, KOBAYASHI M, YAMADA M, et al. Influence of soft reduction with one-piece rolls on center segregation in continuously cast slabs[J]. ISIJ International,1991,31(12):1400.
[38]	刘珂,孙齐松,王立峰,等. 不同厚度连铸板坯的合理总轻压下量[J]. 钢铁研究学报,2017,29(2):111.
[39]	NAKAGAWA T, UMEDA T, MURATA J, et al. Deformation behavior during solidification of steels[J]. ISIJ International,1995,35(6):723.
[40]	WON Y, YEO T, SEOL D. A new criterion for internal crack formation in continuously cast steels[J]. Metallurgical and Materials Transactions B, 2000,31(4):779.
[41]	马海涛, 张炯明, 尹延斌. 压下对重轨钢大方坯内裂纹敏感性的影响[J]. 工程科学学报, 2021, 43(12): 1679.