1. Technology Operations Section,Center Iron and Steel Research Institute,Beijing 100081,China 2. School of Mechanical,Electronic and Control Engineering,Beijing Jiaotong University,Beijing 100044,China
Abstract:The effect of post- forging controlled cooling on the microstructure and hardness of a kind of medium- carbon high- vanadium microalloyed steel (37MnSiVS) for fracture splitting connecting rod was investigated by Gleeble- 3800 thermal simulator. The results showed that the cooling rate had a significant influence on the microstructure and properties of sample. Both the pearlite content and hardness of tested steel gradually increased with the increase of cooling rate. As the cooling rate was higher than 1. 5 °C/s,the bainite was observed in microstructure and the hardness did not increase any more. The forging deformation is advantageous to the formation of fine microstructure and higher content of ferrite. However,the hardness of steel decreased. The fast cooling to about 600 °C followed by proper isothermal treatment significantly promoted strength of tested steel due to the precipitation strengthening effect of many fine and dispersed V(C,N) particles. The results indicated that the differentiation control of forging hardness (strength) could be realized by adjusting post- forging cooling method,which could control the microstructure and precipitation of V(C,N) particles.
收稿日期: 2014-11-24
出版日期: 2015-08-18
引用本文:
陈思联,惠卫军,邵成伟,赵晓丽,董瀚. 控制冷却对中碳高钒非调质钢组织性能的影响[J]. 钢铁, 2015, 50(8): 77-82.
CHEN Si- lian,HUI Wei- jun,SHAO Cheng- wei,ZHAO Xiao- li,DONG Han. Effect of controlled cooling on microstructure and properties of medium- carbon high- vanadium microalloyed steel. Iron and Steel, 2015, 50(8): 77-82.
Jahazi M, Eghbali B. The influence of hot forging conditions on the microstructure and mechanical properties of two microalloyed steels[J]. Journal of Materials Processing Technology, 2001, 113:594-598.
[5]
Jahazi M, Eghbali B. The influence of hot forging conditions on the microstructure and mechanical properties of two microalloyed steels[J]. Journal of Materials Processing Technology, 2001, 113:594-598.
[6]
Khodabandeh A R, Jahazi M, Yue S, Bocher P. Impact toughness and tensile properties improvement through microstructure control in hot forged Nb-V microalloyed steel[J]. ISIJ International, 2005, 45(2):272-280.
[6]
Khodabandeh A R, Jahazi M, Yue S, Bocher P. Impact toughness and tensile properties improvement through microstructure control in hot forged Nb-V microalloyed steel[J]. ISIJ International, 2005, 45(2):272-280.
[7]
Dini G, Vaghefi M M, Shafyei A. The influence of reheating temperature and direct-cooling rate after forging on microstructure and mechanical properties of V-microalloyed steel 38MnSiVS5[J]. ISIJ International, 2006, 46:89-92.
[7]
Dini G, Vaghefi M M, Shafyei A. The influence of reheating temperature and direct-cooling rate after forging on microstructure and mechanical properties of V-microalloyed steel 38MnSiVS5[J]. ISIJ International, 2006, 46:89-92.
[8]
Gündüz S, Capar A. Influence of forging and cooling rate on microstructure and properties of medium carbon microalloy forging steel, Journal of Materials Science, 2006, 41:561-564.
[8]
Gündüz S, Capar A. Influence of forging and cooling rate on microstructure and properties of medium carbon microalloy forging steel, Journal of Materials Science, 2006, 41:561-564.
[9]
Khodabandeh A R, Jahazi M, Yue S, Aghdashi S T. The determination of optimum forging conditions for the production of high strength-high impact toughness automobile parts[J]. Materials and Manufacturing Processes, 2006, 21:105-110.
[9]
Khodabandeh A R, Jahazi M, Yue S, Aghdashi S T. The determination of optimum forging conditions for the production of high strength-high impact toughness automobile parts[J]. Materials and Manufacturing Processes, 2006, 21:105-110.
[10]
Rasouli D, Khameneh Asl S, Akbarzadeh A, Daneshi G H. Effect of cooling rate on the microstructure and mechanical properties of microalloyed forging steel. Journal of Materials Processing Technology, 2008, 206:92-98.
[10]
Rasouli D, Khameneh Asl S, Akbarzadeh A, Daneshi G H. Effect of cooling rate on the microstructure and mechanical properties of microalloyed forging steel. Journal of Materials Processing Technology, 2008, 206:92-98.
Kaynar A, Gündüz S, Türkmen M. Investigation on the behaviour of medium carbon and vanadium microalloyed steels by hot forging test[J]. Materials and Design, 2013, 51:819-825.
[12]
Kaynar A, Gündüz S, Türkmen M. Investigation on the behaviour of medium carbon and vanadium microalloyed steels by hot forging test[J]. Materials and Design, 2013, 51:819-825.
[13]
Ceschini L, Marconi A, Martini C, Morri A, Di Schino A. Tensile and impact behaviour of a microalloyed medium carbon steel: effect of the cooling condition and corresponding microstructure[J]. Materials and Design, 2013, 45:171-178.
[13]
Ceschini L, Marconi A, Martini C, Morri A, Di Schino A. Tensile and impact behaviour of a microalloyed medium carbon steel: effect of the cooling condition and corresponding microstructure[J]. Materials and Design, 2013, 45:171-178.
[14]
曹正. 汽车发动机连杆材料的现状及发展趋势[J]. 汽车工艺与材料,2007, (1):7-10.
[14]
曹正. 汽车发动机连杆材料的现状及发展趋势[J]. 汽车工艺与材料,2007, (1):7-10.
[15]
Bariani P F, Bruschi S. Modeling the forging and post-forging cooling of C70S6 conrods[J]. Journal of Materials Processing Technology, 2005, 167:529-535.
[15]
Bariani P F, Bruschi S. Modeling the forging and post-forging cooling of C70S6 conrods[J]. Journal of Materials Processing Technology, 2005, 167:529-535.
Zhang X Z, Cai Q Z, Zhou G F, Chen Q F, Xiong Y Z. Microstructure and mechanical properties of V-Ti-N microalloyed steel used for fracture splitting connecting rod[J]. Journal of Materials Science, 2011, 46:1789-1795.
[17]
Zhang X Z, Cai Q Z, Zhou G F, Chen Q F, Xiong Y Z. Microstructure and mechanical properties of V-Ti-N microalloyed steel used for fracture splitting connecting rod[J]. Journal of Materials Science, 2011, 46:1789-1795.
Chiba T, Miyamoto M, Lkeshita S, Hamada K, Satoh T. Effects of alloying element on strength and toughness of microalloyed steels[R]. SAE Technical Paper Series, 1996, No. 960310.
[19]
Chiba T, Miyamoto M, Lkeshita S, Hamada K, Satoh T. Effects of alloying element on strength and toughness of microalloyed steels[R]. SAE Technical Paper Series, 1996, No. 960310.
[20]
Miyamoto G, Hori R, Poorganji B, Furuhara T. Interphase precipitation of VC and resultant hardening in V-added medium carbon steels[J]. ISIJ International, 2011, 51(10):1733-1739.
[20]
Miyamoto G, Hori R, Poorganji B, Furuhara T. Interphase precipitation of VC and resultant hardening in V-added medium carbon steels[J]. ISIJ International, 2011, 51(10):1733-1739.
[21]
翁宇庆 等. 超细晶钢—钢的组织细化理论与控制技术[M]. 北京:冶金工业出版社,2003.
[21]
翁宇庆 等. 超细晶钢—钢的组织细化理论与控制技术[M]. 北京:冶金工业出版社,2003.
[22]
Quispe A, Medina S F, Valles P. Recrystallization-induced precipitation interaction in a medium carbon vanadium microalloyed steel[J]. ISIJ International, 1997, 37(8):783-788.
[22]
Quispe A, Medina S F, Valles P. Recrystallization-induced precipitation interaction in a medium carbon vanadium microalloyed steel[J]. ISIJ International, 1997, 37(8):783-788.