Effect of solute partition coefficient and TiN precipitation on micro-segregation of 22MnB5 steel
GUO Wei1,2, LONG Mu-jun 1,2, WU Jia-lu1,2, ZHANG Hao-hao1,2, AI Song-yuan1,2, CHEN Deng-fu1,2
1. School of Materials Science and Engineering, Chongqing University, Chongqing 400044, China; 2. Chongqing Key Laboratory of Vanadium and Titanium Metallurgy and New Materials, Chongqing University, Chongqing 400044, China
Abstract:In order to improve the micro solute segregation in solidification process the accuracy of the model calculation, based on the solute distribution coefficient and the inclusion of the important influence to the solute segregation, this study quantitatively analyses the solute distribution coefficient and separation effect on solidification process of solute elements content of TiN, provide theoretical reference for the research on high strength steel solidification process of micro alloy. A solute microsegregation model coupled with TiN precipitation thermodynamic model was established for 22MnB5 steel, and the effects of temperature and solidification path on solute distribution coefficient were investigated. The results show that the phase transition has greater effects on kTi (titanium distribution coefficient) and kN (nitrogen distribution coefficient) than the temperature. When the solid phase ratio is 0.74, the phase transition from L+δ to L+γ occurs, kTi decreases from 0.26 to 0.20, and the degree of titanium segregation increases. kN increased from 0.30 to 0.46, and the degree of nitrogen segregation decreased. When the solid phase ratio fs is 0.43, TiN begins to precipitate. When the effect of TiN precipitation on microstructure segregation is not considered, the mass percent of Ti and N in the liquid phase at the end of solidification is 0.286% and 0.005 6%, respectively. When TiN precipitation is considered, the mass percent of Ti and N in the liquid phase at the end of solidification are 0.237% and 0.001 9%, which decrease by 17.2% and 66.9%, respectively. At the same time, due to the high degree of titanium segregation during solidification, the enrichment of titanium at the solidification front is enough to offset the consumption of TiN precipitation, while the mass percent of initial nitrogen in steel is low, and the trend of nitrogen segregation decreases with the solidification process, and the degree of solute nitrogen segregation is also reduced under the influence of the transformation from L+δ to L+γ phase. So the segregation of solute nitrogen at the solidification front is not enough to offset the consumption of TiN precipitation. Therefore, the mass percent of nitrogen in the liquid phase at the solidification front increases to decrease obviously due to the precipitation of TiN, while the segregation degree of titanium only weakens at the end of solidification.
郭伟, 龙木军, 吴家璐, 张浩浩, 艾松元, 陈登福. 22MnB5钢溶质分配系数及TiN析出对微观偏析的影响[J]. 钢铁, 2022, 57(3): 44-54.
GUO Wei, LONG Mu-jun , WU Jia-lu, ZHANG Hao-hao, AI Song-yuan, CHEN Deng-fu. Effect of solute partition coefficient and TiN precipitation on micro-segregation of 22MnB5 steel[J]. Iron and Steel, 2022, 57(3): 44-54.
[1] 刘安民, 冯毅, 赵岩,等. 铌钒微合金化对22MnB5热成形钢显微组织与性能的影响[J]. 机械工程材料, 2019, 43(5): 34.(LIU An-min, FENG Yi, ZHAO Yan, et al. Effect of niob-vanadium microalloying on microstructure and properties of 22MnB5 hot-formed steel[J]. Mechanical Engineering Materials, 2019, 43(5): 34.) [2] 杨跃标,邓深,樊雷,等. 钛微合金化高强钢的组织性能及强化机制[J]. 钢铁, 2019, 54(10): 72. (YANG Yue-biao,DENG Shen,FAN Lei,et al. Microstructure,mechanical properties and strengthening mechanism of Ti microalloyed high strength steel[J]. Iron and Steel, 2019, 54(10): 72.) [3] 王华,杨洪林,何燕霖,等.连退工艺对 22MnB5 钢性能的影响规律及显微组织分析[J].上海金属,2015,37(6):15.(WANG Hua,YANG Hong-lin,HE Yan-lin,et al. Effect of annealing process on the performance and microstructure of 22MnB5 steel[J]. Shanghai Metals,2015,37(6):15.) [4] 赵光伟, 石增敏, 叶喜葱,等. 合金凝固微观偏析模型化研究进展[J]. 材料导报, 2014,28(3): 118.(ZHAO Guang-wei, SHI Zeng-min,YE Xi-cong, et al. Advances in modeling of microstructure segregation during solidification of alloys[J]. Materials Reports,2014,28(3): 118.) [5] 李光瀛,马鸣图,张宜生,等. 超高强塑性汽车构件的先进热成形处理AHFT深加工技术[J]. 轧钢 , 2015, 32(3): 1.(LI Guang-ying, MA Ming-tu, ZHANG Yi-sheng,et al. Advanced hot forming treatment AHFT of deep working technology for ultra-high-strength-ductility auto-parts[J]. Steel Rolling , 2015, 32(3): 1.) [6] Gladman T. The Physical Metallurgy of Microalloyed Steels[M]. [S.L.]:Maney Publishing, 1997. [7] 罗森, 朱苗勇, 祭程,等. 钢连铸过程的溶质微观偏析模型[J]. 钢铁, 2010,45(6):31.(LUO Sen, ZHU Miao-yong, JI Cheng, et al.Solute microsegregation model for continuous casting of steel[J]. Iron and Steel, 2010,45(6):31.) [8] 朱立光, 刘震,韩毅华. ND钢连铸坯两相区内的微观偏析模型[J]. 工程科学学报, 2019,41(4): 461.(ZHU Li-guang, LIU Zhen, HAN Yi-hua. Microscopic segregation model of ND steel continuous casting billet in two phase zone[J]. Chinese Journal of Engineering, 2019,41(4): 461.) [9] 邓彪,易红亮,王国栋. Mo对22MnB5钢板热冲压过程中高温氧化行为的影响[J]. 轧钢, 2020, 37(5): 6.(DENG Biao,YI Hong-liang,WANG Guo-dong. Effect of Mo on high temperature oxidation behavior of 22MnB5 steel sheet during hot stamping[J]. Steel Rolling, 2020, 37(5): 6.) [10] 王存宇,周明博,李晓东,等. 温成形中锰钢的组织性能评价[J]. 钢铁, 2019, 54(10): 58.(WANG Cun-yu,ZHOU Ming-bo,LI Xiao-dong,et al. Evaluation of microstructure and properties of warm stamped medium manganese steel[J]. Iron and Steel, 2019, 54(10): 58.) [11] 韩志强, 蔡开科. 连铸坯中微观偏析的模型研究[J]. 金属学报,2000,36(8): 869.(HAN Zhi-qiang, CAI Kai-ke. Model study of microsegregation in continuous casting billet[J].Acta Metallurgica Sinica,2000,36(8): 869.) [12] 李尧, 成国光, 鲁金龙,等. 20CrMnTi齿轮钢中TiN夹杂物的特征与分布[J]. 中国冶金, 2020, 30(12): 28. (LI Yao, CHENG Guo-guang, LU Jin-long,et al. Characteristics and distribution of TiN inclusions in 20CrMnTi gear steel[J]. China Metallurgy, 2020, 30(12): 28.) [13] 李天生, 王福明, 李长荣,等. 含Nb高钼H13钢凝固过程中合金元素的微观偏析[J]. 特种铸造及有色合金, 2013, 33(3): 216.(LI Tian-sheng, WANG Fu-ming, LI Chang-rong, et al.Microstructure segregation of alloying elements in high molybdenum H13 steel containing Nb during solidification[J]. Special-cast and Non-ferrous Alloys, 2013, 33(3): 216.) [14] Kagawa A, Hirata M, Sakamoto Y. Solute partitioning on solidification of nickel-base ternary alloys[J]. Journal of Materials Science, 1990, 25(12):5063. [15] Imai N, Tanaka T, Yuki T, et al. Equilibrium distribution of sn between solid and liquid phases in Fe-Sn and Fe-C-Sn alloys[J]. Tetsu- to- Hagane, 2009, 77(2):224. [16] Hobbs R A, Tin S, Rae C. A castability model based on elemental solid-liquid partitioning in advanced nickel-base single-crystal superalloys[J]. Metallurgical and Materials Transactions A, 2005, 36(10):2761. [17] GUI Lin-tao, MU Jun. Quantitative effects of phase transition on solute partition coefficient,inclusion precipitation, and microsegregation for high-sulfur steel solidification[J]. Journal of Materials Science and Technology, 2019, 35(10): 265. [18] Goto H, Miyazawa K I, Yamaguchi K I, et al. Effect of cooling rate on oxide precipitation during solidification of low carbon steels[J]. ISIJ International, 1994, 34(5):414. [19] 张会全, 郑少波, 郑庆,等. 钢液凝固过程中微观偏析和钛氧夹杂生成的耦合模型[J]. 金属学报, 2006, 42(7):745.(ZHANG Hui-quan, ZHENG Shao-bo, ZHENG Qing, et al.Coupling model of microstructure segregation and Ti-O inclusion formation during solidification of molten steel[J].Acta Metallurgica Sinica, 2006, 42(7):745.) [20] Prikryl M, Kroupa A, Weatherly G C, et al. Precipitation behavior in a medium carbon, Ti-V-N microalloyed steel[J]. Metall Mater Trans A,1996,27(5):1149. [21] FU J, QIU W, NIE Q, et al. Precipitation of TiN during solidification of AISI 439 stainless steel[J]. Journal of Alloys and Compounds, 2017, 699:938. [22] 雍岐龙, 孙新军, 郑磊,等. 钢铁材料中第二相的作用[J]. 科技创新导报, 2009(8):2.(YONG Qi-long, SUN Xin-jun, ZHENG Lei, et al.Role of the second phase in iron and steel materials[J]. Science and Technology Innovation Herald, 2009(8):2.) [23] Voller V R, Beckermann C. A unified model of microsegregation and coarsening[J]. Metallurgical and Materials Transactions A, 1999, 30(8):2183. [24] Won Y M, Thomas B G. Simple model of microsegregation during solidification of steels[J]. Metall Mater Trans A, 2001,32(7):1755. [25] LI K M, YANG Y J, WANG Z G, et al. Microsegregation and homogenizing treatment of GH350 ingot[J]. Journal of Iron and Steel Research, 2012, 24(7):54. [26] WANG Y, BAO Y, WANG M, et al. Precipitation and control of BN inclusions in 42CrMo steel and their effect on machinability[J]. International Journal of Minerals, Metallurgy, and Materials, 2013, 20(9): 842. [27] Kawashita Y, Suito H.Precipitation behavior of Al-Ti on inclusions in unidirectionally solidified Fe-30 mass% Ni alloy[J]. ISIJ International, 1995, 35(12): 1468. [28] 黄希祜. 钢铁冶金原理[M]. 北京: 冶金工业出版社, 2002.(HUANG Xi-gu.Principle of Iron and Steelmetallurgy[M]. Beijing: Metallurgical Industry Press, 2002.) [29] 傅杰, 柳得橹. 微合金钢中TiN的析出规律研究[J]. 金属学报, 2000, 36(8):801.(FU Jie,LIU De-lu. Study on precipitation of TiN in microalloy steel[J].Acta Metallurgica Sinica, 2000, 36(8):801.) [30] 雍岐龙. 钢铁材料中的第二相[M]. 北京:冶金工业出版社, 2006.(YONG Qi-long.The Second Phase in Iron and Steel[M].Beijing:Metallurgical Industry Press, 2006.) [31] 孙彦辉, 高宇, 王龙岗,等. SAPH440钢凝固过程中TiN析出模型[J]. 炼钢, 2011(3):51.(SUN Yan-hui, GAO Yu, WANG Long-gang, et al. TiN precipitation model of SAPH440 steel during solidification[J]. Steelmaking, 2011(3):51.) [32] 周利刚. CSP微合金化钢第二相析出、力学性能及变形行为研究[D]. 武汉:武汉科技大学, 2009.(ZHOU Li-gang. Study on Precipitation, Mechanical Properties and Deformation Behavior of the Second Phase of CSP Microalloyed Steel[D].Wuhan:Wuhan University of Science and Technology, 2009.) [33] 毛新平, 霍向东, 康永林,等. TSCR流程生产钛微合金化高强耐候钢中的析出物[J]. 北京科技大学学报, 2006, 28(11):6.(MAO Xin-ping, HUO Xiang-dong, KANG Yong-lin, et al.Precipitates in titanium microalloyed high strength weathering steel were produced by TSCR process[J]. Journal of University of Science and Technology Beijing, 2006, 28(11):6.)