25CrMo钢锭点状偏析区微观组织特点

doi:10.13228/j.boyuan.issn0449-749x.20160250

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (0 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要为了研究钢锭点状偏析区微观组织特点，对CrMo钢锻坯中的斑点偏析区域进行了分析研究。研究表明，钢坯中的元素偏析区沿锻造方向拉伸且尺寸较小，可判断原铸锭中的偏析为3个维度方向尺寸相近的点状偏析。偏析区中铬、钼元素质量分数相对较高，在冷却后点状偏聚区形成贝氏体组织，与基体的铁素体、珠光体组织呈交错分布的特征，且夹杂物在偏析区富集比较明显，局部偏析区还存在气孔。钢中的点状偏析的出现主要原因是钢液凝固前沿过冷度降低，在成分过冷条件下，高熔点铬、钼组元在枝晶表面局部富集，随温度的下降，钢液中MnS夹杂物同时受枝晶表面的物理吸附作用聚集，同时增加了枝晶区域液相的黏度，导致气体溢出困难，在凝固后局部形成气孔。通过提高钢液凝固速度，降低钢液在固液两相区的停留时间，将有效缓解钢锭中斑点偏析的形成。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	邹长飞
	韦贤毅
	梁宇
	杨明

关键词 ： 25CrMo, 点状偏析, 夹杂物, 气孔

Abstract：The freckle type segregation area of CrMo steel ingot was analyzed in the current study， which show that the elements of segregation area were stretching along the direction of forging with smaller size， the segregation in the primary ingot casting would be called the similar size of the spot segregation but in three dimensions. In this segregation area， with the relatively high element concentration of Cr and Mo， the bainite structures were formed after cooling and distributed in cross with the structures of the ferrite and pearlite in the matrix structure. Besides， the enrichment of inclusions in segregation area was obvious and partial areas existed air hole existed in some areas. The emergence of spot segregation in steel mainly was due to reducing the degree of under cooling at the front of solidified shell. Under constitutional super cooling condition， highly melting point constituent element Cr and Mo will partially enrich on the surface of dendritic with the temperature decreasing， the MnS inclusion in liquid steel was gathered by physical absorption of the surface of dendritic. At the same time，the viscosity of liquid phase in dendritic area increased， leading to the difficult release of gas， which will partially form air hole after solidification. The formation of spot segregation in ingots will be effectively reduced by improving the solidification rate of liquid steel and reducing its retention time in solid-liquid phase region.

收稿日期: 2016-06-08 出版日期: 2017-03-10

PACS:

TF77

引用本文:

邹长飞，杨接明３，韦贤毅，梁宇，杨明，. 25CrMo钢锭点状偏析区微观组织特点[J]. 钢铁, 2017, 52(3): 21-26. ZOU Chang-fei，，YANG Jie-ming，WEI Xian-yi，，LIANG Yu，，YANG Ming，. Microstructure characteristics of spot segregation of 25CrMo steel ingot. Iron and Steel, 2017, 52(3): 21-26.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20160250 或 http://www.chinamet.cn/Jweb_gt/CN/Y2017/V52/I3/21

[1]	张轲, 牛焱, 吴维涛.钢在还原性含氯气氛中的高温腐蚀行为[J].金属学报, 2003, 39(5):541-543
[1]	张轲, 牛焱, 吴维涛.钢在还原性含氯气氛中的高温腐蚀行为[J].金属学报, 2003, 39(5):541-543
[2]	ZHANG Ke, NIUYan, WUWei-tao.High temperature corrosion behavior of steel 225CrMo in reducing atmosphere containing chlorine[J].Act MetallurgicalSonica, 2003, 39(5):541-543
[2]	ZHANG Ke, NIUYan, WUWei-tao.High temperature corrosion behavior of steel 225CrMo in reducing atmosphere containing chlorine[J].Act MetallurgicalSonica, 2003, 39(5):541-543
[3]	刘庚武.材料的锻造与热处理工艺研究锻压技术[J].锻压技术, 2010, 35(1):162-164
[3]	刘庚武.材料的锻造与热处理工艺研究锻压技术[J].锻压技术, 2010, 35(1):162-164
[4]	LIUGang-wu.Forging and heat treatment technology study of EA4T materialForging & Stamping Technology,2010,(1): 162-164.[J]., 2010, 35(1):162-164
[4]	LIUGang-wu.Forging and heat treatment technology study of EA4T materialForging & Stamping Technology,2010,(1): 162-164.[J]., 2010, 35(1):162-164
[5]	MehrabianR, Keane M A, Flemings M C.Experiments on macrosegregation and freckle formation[J].Metallurgical & Materials Transactions B, 1970, 1(11):3238-3241
[5]	MehrabianR, Keane M A, Flemings M C.Experiments on macrosegregation and freckle formation[J].Metallurgical & Materials Transactions B, 1970, 1(11):3238-3241
[6]	王允实, 侯翠萍, 王明贤.一种变形铁基高温合金中的点状偏析[J].金属学报, 1980, 16(1):22-128
[6]	王允实, 侯翠萍, 王明贤.一种变形铁基高温合金中的点状偏析[J].金属学报, 1980, 16(1):22-128
[7]	WANGYun-shi, HOU Cui-ping, WANG Ming-xian.An investigation of freckles in iron-nickle base wroughtsuperalloy[J].Acta Metallurgical Sinica, 1980, 16(01):22-128
[7]	WANGYun-shi, HOU Cui-ping, WANG Ming-xian.An investigation of freckles in iron-nickle base wroughtsuperalloy[J].Acta Metallurgical Sinica, 1980, 16(01):22-128
[8]	KaragaddeS, YuanL, ShevchenkoN, etal.Dmicrostructural model of freckle formation validated using in situ experiments[J].ActaMaterialia, 2014, 79(30):168-180
[8]	KaragaddeS, YuanL, ShevchenkoN, etal.Dmicrostructural model of freckle formation validated using in situ experiments[J].ActaMaterialia, 2014, 79(30):168-180
[9]	Yuan, Lang, Lee, etal.A new mechanism for freckle initiation based on microstructural level simulation[J].ActaMaterialia, 2012, 60(12):4917-4926
[9]	Yuan, Lang, Lee, etal.A new mechanism for freckle initiation based on microstructural level simulation[J].ActaMaterialia, 2012, 60(12):4917-4926
[10]	Li D, Chen X Q, FuP, etal.Inclusion flotation-driven channel segregation in solidifying steels[J].Nature Communications, 2014, 5(5):5572-5572
[10]	Li D, Chen X Q, FuP, etal.Inclusion flotation-driven channel segregation in solidifying steels[J].Nature Communications, 2014, 5(5):5572-5572
[11]	Cao Y F, ChenY, Li D Z.Formation mechanism of channel segregation in carbon steels by inclusion flotation: X-ray microtomography characterization and multi-phase flow modeling[J].ActaMaterialia, 2016, 107:325-336.[J]., 2016, (107):325-336[J]., 2016, (107):318-321
[11]	Cao Y F, ChenY, Li D Z.Formation mechanism of channel segregation in carbon steels by inclusion flotation: X-ray microtomography characterization and multi-phase flow modeling[J].ActaMaterialia, 2016, 107:325-336.[J]., 2016, (107):325-336[J]., 2016, (107):318-321
[12]	杨凡中.钢中点状偏析形成过程的探讨[J].四川冶金, 1985(3)：52-55．[J]., 1985, 3:-[J].四川冶金, 1985, (3):52-55
[12]	杨凡中.钢中点状偏析形成过程的探讨[J].四川冶金, 1985(3)：52-55．[J]., 1985, 3:-[J].四川冶金, 1985, (3):52-55
[13]	YANG Fang-zhong.The discussion of formation process of the spot segregation in steel[J].Sichuan Metallurgy, 1985(3)：52-55．[J]., 1985, (3):52-55
[13]	YANG Fang-zhong.The discussion of formation process of the spot segregation in steel[J].Sichuan Metallurgy, 1985(3)：52-55．[J]., 1985, (3):52-55
[14]	姚凤祥.电渣重熔辊坯用钢点状偏析形成过程及其过程控制[J].大型铸锻件, 2010(2):12-14.[J].大型铸锻件, 2010, (2):12-14
[14]	姚凤祥.电渣重熔辊坯用钢点状偏析形成过程及其过程控制[J].大型铸锻件, 2010(2):12-14.[J].大型铸锻件, 2010, (2):12-14
[15]	YAO Feng-xiang.Forming process of pointsegregationand its process controlinelectroslagremelting roll blank[J].Heave Casting And Foring, 2010(2):12-14.[J]., 2010, (2):12-14
[15]	YAO Feng-xiang.Forming process of pointsegregationand its process controlinelectroslagremelting roll blank[J].Heave Casting And Foring, 2010(2):12-14.[J]., 2010, (2):12-14
[16]	吴杰, 张瑞明.G50钢斑点状偏析的准确评定[J].特钢技术, 2015(2):50-53.[J].特钢技术, 2015, (2):50-53
[16]	吴杰, 张瑞明.G50钢斑点状偏析的准确评定[J].特钢技术, 2015(2):50-53.[J].特钢技术, 2015, (2):50-53
[17]	WU Jie, ZHANGRui-ming.Correctevaluation on spot-shaped segregations inG50 steel[J].Special Steel Technology, 2015(2):50-53.[J]., 2015, (2):50-53
[17]	WU Jie, ZHANGRui-ming.Correctevaluation on spot-shaped segregations inG50 steel[J].Special Steel Technology, 2015(2):50-53.[J]., 2015, (2):50-53
[18]	GUO Z, Kimura N, Tagashira S, et al.Kinetics and crystallography of intragranular pearlite transformation nucleated at (MnS +VC)complex precipitates in hypereutectoid Fe-Mn-C alloys[J]. ISIJ Int., 2002, 42: 1033～1041.[J]., 2002, 42(9):1033-1041
[18]	GUO Z, Kimura N, Tagashira S, et al.Kinetics and crystallography of intragranular pearlite transformation nucleated at (MnS +VC)complex precipitates in hypereutectoid Fe-Mn-C alloys[J]. ISIJ Int., 2002, 42: 1033～1041.[J]., 2002, 42(9):1033-1041
[19]	ZHANG Z and Farrar R A.Role of non-metallic inclusions in formation of acicular ferrite in low alloy weld metals[J]. Mater.Sci.Technol, 1996, 12:237-260.[J]., 1996, (12):237-260
[19]	ZHANG Z and Farrar R A.Role of non-metallic inclusions in formation of acicular ferrite in low alloy weld metals[J]. Mater.Sci.Technol, 1996, 12:237-260.[J]., 1996, (12):237-260
[20]	梁高飞, 王成全, 方园.不锈钢熔化过程中夹杂物在固-液糊状区漂移与聚集行为的原位观察[J].金属学报, 2006, 42(7):708-714
[20]	梁高飞, 王成全, 方园.不锈钢熔化过程中夹杂物在固-液糊状区漂移与聚集行为的原位观察[J].金属学报, 2006, 42(7):708-714
[21]	LIANG Gao-fei, WANGCheng-quan, FANGYuan.In situ observation on movement and agglomeration of inclusion in solid-liquid mush zone during melting of stainless steel AISI304[J].Acta Metallurgy Sinica, 2006, 42(7):708-714
[21]	LIANG Gao-fei, WANGCheng-quan, FANGYuan.In situ observation on movement and agglomeration of inclusion in solid-liquid mush zone during melting of stainless steel AISI304[J].Acta Metallurgy Sinica, 2006, 42(7):708-714
[22]	Yin H, ShibataH, EmiT, etal.In-situ" Observation of Collision,Agglomeration and Cluster Formation of Alumina Inclusion Particles on Steel Melts[J].Isij International, 1997, 37(10):936-945
[22]	Yin H, ShibataH, EmiT, etal.In-situ" Observation of Collision,Agglomeration and Cluster Formation of Alumina Inclusion Particles on Steel Melts[J].Isij International, 1997, 37(10):936-945
[23]	ShangguanD, AhujaS, Stefanescu D M.An analytical model for the interaction between an insoluble particle and an advancing solidliquid interface[J].Metallurgical & Materials Transactions A, 1992, 23(2):669-680
[23]	ShangguanD, AhujaS, Stefanescu D M.An analytical model for the interaction between an insoluble particle and an advancing solidliquid interface[J].Metallurgical & Materials Transactions A, 1992, 23(2):669-680
[24]	Valdez M E, WangY, SridharS.MnS precipitation behavior in re-sulfurized steels with intermediate levels of sulfur[J].Steel Research International, 2005, 76(4):306-312
[24]	Valdez M E, WangY, SridharS.MnS precipitation behavior in re-sulfurized steels with intermediate levels of sulfur[J].Steel Research International, 2005, 76(4):306-312
[25]	雷少龙, 姜敏, 杨叠.脱氧钢中氧化物对析出的影响[J].北京科技大学学报, 2013, 35(11):1448-
[25]	雷少龙, 姜敏, 杨叠.脱氧钢中氧化物对析出的影响[J].北京科技大学学报, 2013, 35(11):1448-
[26]	LEI Shao-long, JIANGMin, YANGDie.E?ect of oxides on MnS precipitation in aluminum-deoxidized steel[J].Journal of University of Science and Technology Beijing, 2013, 35(11):1448-
[26]	LEI Shao-long, JIANGMin, YANGDie.E?ect of oxides on MnS precipitation in aluminum-deoxidized steel[J].Journal of University of Science and Technology Beijing, 2013, 35(11):1448-
[27]	杨成威, 吕迺冰, 卓晓军, 等.MnS在Ti—Al 复合脱氧氧化物上的析出研究[J].钢铁, 2010 (11): 32-36.[J].钢铁, 2010, 45(11):32-36
[27]	杨成威, 吕迺冰, 卓晓军, 等.MnS在Ti—Al 复合脱氧氧化物上的析出研究[J].钢铁, 2010 (11): 32-36.[J].钢铁, 2010, 45(11):32-36
[28]	YANG Cheng-wei, LVNai-bing, ZHOUXiao-jun, Study of MnSprecipitation on Ti-Al Complex de-oxidation inclusions[J].Iron and Steel, 2010 (11): 32-36.[J]., 2010, 45(11):32-36
[28]	YANG Cheng-wei, LVNai-bing, ZHOUXiao-jun, Study of MnSprecipitation on Ti-Al Complex de-oxidation inclusions[J].Iron and Steel, 2010 (11): 32-36.[J]., 2010, 45(11):32-36
[29]	张玉妥, 边书, 韩维新.25CrMo钢端淬试验改进与淬透性分析[J].材料热处理学报, 2015, 02:162-165.[J].材料热处理学报, 2015, 36(2):162-165
[29]	张玉妥, 边书, 韩维新.25CrMo钢端淬试验改进与淬透性分析[J].材料热处理学报, 2015, 02:162-165.[J].材料热处理学报, 2015, 36(2):162-165
[30]	ZHANG Yu-tuo, BIANShu, HANWei-xin.Improvement of end quench test and hardenability analysis of 25CrMo steel[J].Transactions of Materials and Heat Treatment, 2015, 02:162-165.[J]., 2015, 36(2):162-165
[30]	ZHANG Yu-tuo, BIANShu, HANWei-xin.Improvement of end quench test and hardenability analysis of 25CrMo steel[J].Transactions of Materials and Heat Treatment, 2015, 02:162-165.[J]., 2015, 36(2):162-165
[31]	ZHANG Y, SHU B, HANW.Effect of Mn on hardenability of 25CrMo axle steel by an improved end-quench test[J].China Foundry, 2012, 9(4):318-321
[31]	ZHANG Y, SHU B, HANW.Effect of Mn on hardenability of 25CrMo axle steel by an improved end-quench test[J].China Foundry, 2012, 9(4):318-321