软熔过程中烧结矿和块矿的交互作用

doi:10.13228/j.boyuan.issn0449-749x.20190094

摘要
图/表
参考文献(22)
相关文章 (15)

全文: PDF (21410 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为更好地明晰块矿的软熔行为并优化其在高炉内的使用,以烧结矿和澳大利亚纽曼混合块矿为研究对象,分别就两者在软熔过程中的物理和化学交互作用进行了试验研究。通过使用中子CT扫描软熔试验试样, 发现1 450 ℃时烧结矿与纽曼混合块矿的混合炉料孔隙度要高于两者单一炉料,即两者间存在着物理交互作用;通过采用扫描电镜和电子探针分析发现,1 200～1 300 ℃温度范围内烧结矿中钙和镁扩散到了块矿中,两者发生了明显的化学交互作用。在物理和化学交互共同作用下,配加约20%纽曼混合块矿的混合炉料软熔行为得到了明显改善,且其性能相似或略好于同碱度的单一烧结矿炉料,这表明块矿和烧结矿混合后能在高炉内形成温度区间更窄、位置更低、透气性更好的软熔带。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	刘新亮
	HONEYANDS Tom
	O′DEA Damien
	MITRA Subhasish
	CHEN Jeff
	邱光君

关键词 ：烧结矿, 块矿, 软熔行为, 孔隙度, 交互作用, 中子CT扫描

Abstract：The main purpose is to better understand the softening and melting (S&M) behaviour of lump in the blast furnace (BF) and how to optimise its use with sinter. As the only ferrous burden material that can be directly charged into the BF, the lump is more environmentally friendly and economically effective than sinters or pellets. Despite this, the lump utilisation in China is lower than that in other countries such as Japan. One of the main concerns is the perception that the S&M properties of individual lump samples are not as good as those of sinter or pellet. However, it has been shown that the high temperature interaction between sinter and lump can largely improve the S&M behaviour of a mixed burden composed of sinter and lump. Both the chemical and physical interaction between a basic sinter and the Newman Blend Lump (NBLL) from Australia were studied using the S&M under load test and the tablet analogue test. The physical interaction was examined using Neutron Computed Tomography scanning on the samples from interrupted S&M under load tests. The void fraction in the ferrous layer of the sinter-NBLL mixture at 1 450 ℃ was found to be higher than that for either the sinter or NBLL only burdens. The chemical interaction was studied using SEM and EPMA, which showed that the Ca and Mg diffused from the basic sinter to neighbouring lump ore particles during the S&M process in the temperature range from 1 200 to 1 300 ℃. Significant improvements were found in the S&M behaviour of a mixed burden with about 20% NBLL because of the changes in the bed structure by the physical interaction and the changes in the melt composition caused by the chemical interaction. The mixed burden performed better or at least no worse than a sinter only burden with the same total basicity. The BF modelling indicates that mixing lump with the sinter burden forms a narrower CZ with higher permeability and lower position in the blast furnace.

Key words： sinter lump softening and melting voidage interaction neutron CT scanning

收稿日期: 2019-03-18

引用本文:

刘新亮, HONEYANDS Tom, O′DEA Damien, MITRA Subhasish, CHEN Jeff, 邱光君. 软熔过程中烧结矿和块矿的交互作用[J]. 钢铁, 2019, 54(12): 19-26. LIU Xin-liang, HONEYANDS Tom, O′DEA Damien, MITRA Subhasish, CHEN Jeff, QIU Guang-jun. Interaction between sinter and lump during softening and melting process. Iron and Steel, 2019, 54(12): 19-26.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20190094 或 http://www.chinamet.cn/Jweb_gt/CN/Y2019/V54/I12/19

[1]	刘杰,张洪宇,周明顺,等. 基于软熔滴落性能的高炉合理炉料结构[J]. 钢铁,2016,51(9):11. (LIU Jie,ZHANG Hong-yu,ZHOU Ming-shun,et al. Rational burden structure of blast furnace based on softening and melting properties[J]. Iron and Steel, 2016,51(9):11.)
[2]	李昌齐,刘树俊. 武钢8号高炉提高块矿比生产实践[J]. 武钢技术,2017,55(3):15. (LI Chang-qi,LIU Shu-jun. Practice of raising lump ore ratio in No. 8 BF of Wuhan Iron and Steel Limited Company[J]. WISCO Technology,2017,55(3):15.)
[3]	钟树周. 高炉用进口块矿代替部分球团矿工业试验[J]. 南方金属,2006(153):25. (ZHONG Shu-zhou. Industrial-scale experiment of partially substituting imported lump ore for imported pellet for BF[J]. Southern Metals,2006(153):25.)
[5]	Natio Masaaki,Takeda Kanji,Matsui Yoshiyuki. Ironmaking technology for the last 100 years: Deployment to advanced technologies from introduction of technological know-how, and evolution to next-generation process[J]. ISIJ International,2015,55(1):7.
[4]	ZHOU Dong-dong, CHENG Shu-sen, WANG Ying-sheng, et al. The production of large blast furnaces during 2016 and future development of ironmaking in China[J]. Ironmaking and Steelmaking,2017,44(10):714.
[6]	褚润林,张利波,王聪渊,等. 宣钢 4 号高炉提高块矿比冶炼实践[J]. 河南冶金,2016,24(4):30. (CHU Run-lin,ZHANG Li-bo,WANG Cong-yuan,et al. Trengthened smelting practice of increasing lump ore proportion on Xuan Steel's No.4 BF[J]. Henan Metallurgy,2016,24 (4):30.)
[7]	卢光辉. 高炉提高块矿比生产实践[J]. 金属世界,2016(2):44. (LU Guang-hui. Practice of improving ore production ratio in blast furnace of Handan Steel[J]. Metal World, 2016(2):44.)
[8]	林国太. 三钢高炉炉料结构调整应用分析[J].福建冶金,2018(26):1. (LIN Guo-tai. Application analysis of furnace material structure adjustment at Sansteel blast furnace[J]. Fujin Metallurgy,2018(26):1.)
[9]	梁清仁,李国权,曹旭. 提高高炉生矿比的生产实践[J]. 四川冶金,2017,39(4):39. (LIANG Qing-ren, LI Guo-quan, CAO Xu. The production practice of raising raw ore ratio of blast furnace[J]. Sichuan Metallurgy,2017,39(4):39.)
[10]	贾文君,刘晓明,魏琼花,等. 邯钢高炉大比例配加澳矿的研究与应用[J]. 河南冶金,2018,26(1):52.(JIA Wen-jun,LIU Xiao-ming,WEI Qiong-hua,et al. Research and application of proportion adding of Australia ore large in blast furnace burden of Hansteel[J]. Henan Metallurgy,2018,26(1):52.)
[11]	WU Sheng-li, HAN Hong-liang, XU Hai-fa, et al. Increasing lump ores proportion in blast furnace based on the high-temperature interactivity of iron bearing materials[J]. ISIJ International,2010,50(5):686.
[5]	Natio Masaaki,Takeda Kanji,Matsui Yoshiyuki. Ironmaking technology for the last 100 years: Deployment to advanced technologies from introduction of technological know-how, and evolution to next-generation process[J]. ISIJ International,2015,55(1):7.
[6]	褚润林,张利波,王聪渊,等. 宣钢 4 号高炉提高块矿比冶炼实践[J]. 河南冶金,2016,24(4):30. (CHU Run-lin,ZHANG Li-bo,WANG Cong-yuan,et al. Trengthened smelting practice of increasing lump ore proportion on Xuan Steel's No.4 BF[J]. Henan Metallurgy,2016,24 (4):30.)
[7]	卢光辉. 高炉提高块矿比生产实践[J]. 金属世界,2016(2):44. (LU Guang-hui. Practice of improving ore production ratio in blast furnace of Handan Steel[J]. Metal World, 2016(2):44.)
[8]	林国太. 三钢高炉炉料结构调整应用分析[J].福建冶金,2018(26):1. (LIN Guo-tai. Application analysis of furnace material structure adjustment at Sansteel blast furnace[J]. Fujin Metallurgy,2018(26):1.)
[9]	梁清仁,李国权,曹旭. 提高高炉生矿比的生产实践[J]. 四川冶金,2017,39(4):39. (LIANG Qing-ren, LI Guo-quan, CAO Xu. The production practice of raising raw ore ratio of blast furnace[J]. Sichuan Metallurgy,2017,39(4):39.)
[10]	贾文君,刘晓明,魏琼花,等. 邯钢高炉大比例配加澳矿的研究与应用[J]. 河南冶金,2018,26(1):52.(JIA Wen-jun,LIU Xiao-ming,WEI Qiong-hua,et al. Research and application of proportion adding of Australia ore large in blast furnace burden of Hansteel[J]. Henan Metallurgy,2018,26(1):52.)
[12]	CHEN Long, XUE Qing-guo, GUO Wen-tao, et al. Study on the interaction behaviour between lump and sinter under the condition of oxygen blast furnace[J]. Ironmaking and Steelmaking,2016,43(6):458.
[11]	WU Sheng-li, HAN Hong-liang, XU Hai-fa, et al. Increasing lump ores proportion in blast furnace based on the high-temperature interactivity of iron bearing materials[J]. ISIJ International,2010,50(5):686.
[13]	LIU Xin-liang, WU Sheng-li, HUANG Wei, et al. Influence of high temperature interaction between sinter and lump ores on the formation behaviour of primary-slags in blast furnace[J]. ISIJ International,2014,54(9):2089.
[12]	CHEN Long, XUE Qing-guo, GUO Wen-tao, et al. Study on the interaction behaviour between lump and sinter under the condition of oxygen blast furnace[J]. Ironmaking and Steelmaking,2016,43(6):458.
[14]	韩涛,李洋,覃开伟,等. 含铁炉料高温交互反应研究在宣化高炉的应用[C]// 2018年全国炼铁学术年会,北京:中国金属学会,2018:148.(HAN Tao,LI Yang,TAN Kai-wei,et al.Application of high temperature interactive reaction of iron containing furnace in Xuanhua blast furnace[C]//2018 National Iron Making Academic Conference.Beijing: The Chinese Society for Metals,2018:148.)
[15]	Loo Chin-Eng, Matthews Leanne, O′dea Damien. Lump ore and sinter behaviour during softening and melting[J]. ISIJ International,2011,51(6):930.
[13]	LIU Xin-liang, WU Sheng-li, HUANG Wei, et al. Influence of high temperature interaction between sinter and lump ores on the formation behaviour of primary-slags in blast furnace[J]. ISIJ International,2014,54(9):2089.
[14]	韩涛,李洋,覃开伟,等. 含铁炉料高温交互反应研究在宣化高炉的应用[C]// 2018年全国炼铁学术年会,北京:中国金属学会,2018:148.(HAN Tao,LI Yang,TAN Kai-wei,et al.Application of high temperature interactive reaction of iron containing furnace in Xuanhua blast furnace[C]//2018 National Iron Making Academic Conference.Beijing: The Chinese Society for Metals,2018:148.)
[15]	Loo Chin-Eng, Matthews Leanne, O′dea Damien. Lump ore and sinter behaviour during softening and melting[J]. ISIJ International,2011,51(6):930.
[16]	WU Sheng-li, SU Bo, LIU Xin-liang. Optimisation of the blast furnace burden based on its primary slag formation behaviour[J]. Ironmaking and Steelmaking,2018,45(1):50.
[17]	Liu Xin-liang, Honeyands Tom, Mitra Subhasish, et al. A novel measurement of voidage in coke and ferrous layers in softening and melting under load test using synchrotron X-ray and neutron computed tomography[J]. ISIJ International,2018,58(11):2150.
[16]	WU Sheng-li, SU Bo, LIU Xin-liang. Optimisation of the blast furnace burden based on its primary slag formation behaviour[J]. Ironmaking and Steelmaking,2018,45(1):50.
[18]	吴胜利,张永忠,苏博,等. 影响烧结工艺过程NOx排放质量浓度的主要因素解析[J]. 工程科学学报,2017,39(5):693. (WU Sheng-li, ZHANG Yong-zhong, SU Bo, et al. Analysis of main factors affecting NOx emissions in sintering process[J].Chinese Journal of Engineering, 2017,39(5):693.)
[19]	朱贺民. 烧结矿碱度、SiO2和MgO含量对烧结冶金性能的影响[J]. 钢铁研究,2006,34(4):17. (ZHU He-min. Effect of basicity, SiO2 and MgO contents of sinter on sinter properties[J]. Research on Iron and Steel, 2006,34(4):17.)
[20]	Loo Chin-Eng, Gareth Penny, Matthews Leanne, et al. Mechanisms determining softening/melting and reduction properties of lumps and pellets[C]//10th CSM Steel Congress.Shanghai: The Chinese Society for Metals,2015:1.
[17]	Liu Xin-liang, Honeyands Tom, Mitra Subhasish, et al. A novel measurement of voidage in coke and ferrous layers in softening and melting under load test using synchrotron X-ray and neutron computed tomography[J]. ISIJ International,2018,58(11):2150.
[18]	吴胜利,张永忠,苏博,等. 影响烧结工艺过程NOx排放质量浓度的主要因素解析[J]. 工程科学学报,2017,39(5):693. (WU Sheng-li, ZHANG Yong-zhong, SU Bo, et al. Analysis of main factors affecting NOx emissions in sintering process[J].Chinese Journal of Engineering, 2017,39(5):693.)
[19]	朱贺民. 烧结矿碱度、SiO2和MgO含量对烧结冶金性能的影响[J]. 钢铁研究,2006,34(4):17. (ZHU He-min. Effect of basicity, SiO2 and MgO contents of sinter on sinter properties[J]. Research on Iron and Steel, 2006,34(4):17.)
[21]	Liu Xin-liang, Honeyands Tom, Evans Geoffrey, et al. A review of high-temperature experimental techniques used to investigate the cohesive zone of the ironmaking blast furnace[J]. Ironmaking and Steelmaking,https://doi.org/10.1080/03019233.2018.1464107.
[20]	Loo Chin-Eng, Gareth Penny, Matthews Leanne, et al. Mechanisms determining softening/melting and reduction properties of lumps and pellets[C]//10th CSM Steel Congress.Shanghai: The Chinese Society for Metals,2015:1.
[21]	Liu Xin-liang, Honeyands Tom, Evans Geoffrey, et al. A review of high-temperature experimental techniques used to investigate the cohesive zone of the ironmaking blast furnace[J]. Ironmaking and Steelmaking,https://doi.org/10.1080/03019233.2018.1464107.
[22]	Allibert M, Gaye H, Geiseler J,et al. Slag Atlas[M]. 2nd ed.Dusseldorf: Verlag Stahleisen GmbH, 1995.
[22]	Allibert M, Gaye H, Geiseler J,et al. Slag Atlas[M]. 2nd ed.Dusseldorf: Verlag Stahleisen GmbH, 1995.