Abstract:Hot-dip Zn-Al-Mg coating is widely used in automobiles and home appliances because of its better notch protection performance and corrosion resistance,and the corrosion resistance of Zn-Al-Mg coated steel sheet is closely related to its phase composition. Therefore,in order to better study the microstructure and phase structure composition of the surface and cross-section of the Zn-Al-Mg coating on the hot-dip low alloy high strength steel. Micro-machining and fine polishing of the coating section by focused ion beam (FIB),a flat,bright and stress-free surface to be observed is prepared. Firstly,the microstructure,morphology and composition of the surface and cross-section of the Zn-Al-Mg coating were preliminarily analyzed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS),secondly,the phase structure and composition of the Zn-Al-Mg coating were accurately determined by means of electron backscatter diffraction (EBSD) Kikuchi pattern calibration. The research shows that the phase composition of the surface of the Zn-Al-Mg coating is the same as that of the cross-section,which is composed of a coarse dendritic primary Zn-rich phase,a relatively fine fishbone-like or dendritic Zn-Mg binary eutectic phase,and more fine grained or striped Zn-Mg-Al ternary eutectic phase. In addition,a large number of nano-precipitated Al-rich phases are uniformly dispersed in the bulk primary Zn-rich phase. The phase structure of the hot-dip Zn-Al-Mg coating was accurately determined by the EBSD Kikuchi pattern calibration. The Zn-Mg binary eutectic phase is Zn-MgZn2 with the same close-packed hexagonal structure,and the finer granular or strip-shaped Zn-Mg-Al ternary eutectic phase is Zn-MgZn2-Al. In addition,the nano-scale Al-rich phase particles precipitated in the primary Zn phase can effectively improve the surface hardness of the coating. At the same time,the edges of the primary Zn phase and the eutectic phase are covered with a layer of MgZn2 phase,which can effectively delay the corrosion process and improve the corrosion resistance of the coating.
崔桂彬, 鞠新华, 严春莲, 马泽军. 热浸镀低合金高强钢Zn-Al-Mg镀层的组织结构表征[J]. 钢铁, 2023, 58(1): 153-160.
CUI Gui-bin, JU Xin-hua, YAN Chun-lian, MA Ze-jun. Microstructure characterization of hot-dip Zn-Al-Mg coating of low alloy high strength steel[J]. Iron and Steel, 2023, 58(1): 153-160.
[1] 陈菡.镀锌防腐工艺[J].钢铁,2007,42(7):38.(CHEN Han. Anticorrosive galvanizing[J]. Iron and Steel,2007,42(7):38.) [2] 张启富,刘邦津,仲海峰.热镀锌技术的最新进展[J].钢铁研究学报,2002,14(4):65.(ZHANG Qi-fu,LIU Bang-jin,ZHONG Hai-feng. Development trend of hot-dip galvanizing technology[J]. Journal of Iron and Steel Research,2002,14(4):65.) [3] Prosek T,Persson B D,Stoulil J,et al. Composition of corrosion products formed on Zn-Mg,Zn-Al and Zn-Al-Mg coatings in model atmospheric conditions[J]. Corrosion Science,2014,86:231. [4] 杨忠,马风雪,孙浩,等.锌铝镁钢板的防腐及涂装性评价[J].电镀与涂饰,2021,40(18):1393.(YANG Zhong,MA Feng-xue,SUN Hao,et al. Evaluation on anticorrosion and paintability of Zn-Al-Mg alloy coated steel sheet[J]. Electroplating and Finishing,2021,40(18):1393.) [5] Prosek T,Nazarov A,Gac A L,et al. Coil-coated Zn-Mg and Zn-Al-Mg: Effect of climatic parameters on the corrosion at cut edges[J]. Progress in Organic Coatings,2015,83:26. [6] YAO C Z,LÜ H B,ZHU T P,et al. Effect of Mg content on microstructure and corrosion behavior of hot dipped Zn-Al-Mg alloys[J]. Journal of Alloys and Compounds,2016,670:239. [7] DONG A P,LI B P,LU Y L,et al. Effect of Mg on the microstructure and morrosion mesistance of the continuously hot-dip galvanizing Zn-Mg coating[J]. Materials,2017,890:1. [8] Proseka T,Hagstrom J,Persson D,et al. Effect of the microstructure of Zn-Al and Zn-Al-Mg model alloys on corrosion stability[J]. Corrosion Science,2016,110:71. [9] 袁训华,林源,张启富.热镀锌铝镁镀层的切边保护性能和耐腐蚀机理[J].中国有色金属学报,2015,25(9):2453.(YUAN Xun-hua,LIN Yuan,ZHANG Qi-fu. Cut-edge protection performance and corrosion resistance mechanisms of galvanized Zn-Al-Mg ahoy coating[J]. The Chinese Journal of Nonferrous Metals,2015,25(9):2453.) [10] 杜昕,张满仓,段生朝,等.高耐蚀锌铝镁镀层研究现状[J].工程科学学报,2019,41(7):847.(DU Xin,ZHANG Man-cang,DUAN Sheng-chao,et al. Research status of high corrosion-resistant Zn-Al-Mg coating[J]. Chinese Journal of Engineering,2019,41(7):847.) [11] 童晨,苏旭平,王建华,等.Mg对Zn-6%Al镀层凝固组织的影响及耐腐蚀性的研究[J].热加工工艺,2012,41(12):99.(TONG Chen,SU Xu-ping,WANG Jian-hua,et al. Effect of Mg addition on solidification structure and corrosion resistance of Zn-6%Al alloy coating[J]. Hot Working Technology,2012,41(12):99.) [12] LIANG H,CHEN S L,CHANG Y A.A thermodynamic description of the Al-Mg-Zn system[J].Metallurgical and Materials Transactions A,1997,28:1725. [13] 邹建国,卢琳.锌铝镁镀层中合金相与耐蚀性的关系研究进展[J].中国有色金属学报,2022,32(7):1934.(ZOU Jian-guo,LU Lin. Research progress on the relationship between alloy phase and corrosion resistance in Zn-Al-Mg coating[J]. The Chinese Journal of Nonferrous Metals,2022,32(7):1934.) [14] 吕家舜,李锋,杨洪刚,等.热浸镀锌铝镁镀层微观组织试验[J].钢铁,2013,48(6):75.(LÜ Jia-shun,LI Feng,YANG Hong-gang,et al. Experiments investigation on microstructure of galvanized Zn-Al-Mg coated steel sheet[J]. Iron and Steel,2013,48(6):75.) [15] 胡璠,徐巍,王林烽,等.桥梁缆索钢丝热浸镀Zn-Al-Mg镀层的组织与耐蚀性能研究[J].表面技术,2021,50(11):279.(HU Fan,XU Wei,WANG Lin-feng,et al. Microstructure and corrosion resistance of hot dip Zn-Al-Mg coating for bridge cable wire[J]. Surface Technology,2021,50(11):279.) [16] 李锋,吕家舜,杨洪刚,等.热浸镀Zn11Al3Mg0.2Si合金镀层微观组织实验研究[J].表面技术,2011,40(3):32.(LI Feng,LÜ Jia-shun,YANG Hong-gang,et al. The experiment research of microstructure of hot-dip galvanized Zn11Al3Mg0.2Si alloy coating[J]. Surface Technology,2011,40(3):32.) [17] Lebozec N,Thoerry D,Persson D,et al. Influence of microstructure of zinc-aluminium-magnesium alloy coated steel on the corrosion behavior in outdoor marine atmosphere[J].Surface and Coatings Technology,2019,374:897. [18] ZHANG Z Y,YUE Z W,LI X G,et al. Microstructure and corrosion resistance of Zn-Al-Mg alloy diffusion coating developed on carbon steel by hot dipping[J]. International Journal of Electrochemical Science,2020,15:5512. [19] 童晨,苏旭平,李智,等.浸镀Zn-6%Al-3%Mg镀层合金层生长研究[J].材料工程,2013(7):54.(TONG Chen,SU Xu-ping,LI Zhi,et al. Research on hot-dipped Zn-6%Al-3%Mg alloy coatings intermetallics layer growth[J]. Journal of Materials Engineering,2013(7):54.) [20] Truglas T,Duchoslav J,Rienerd C,et al. Correlative characterization of Zn-Al-Mg coatings by electron microscopy and FIB tomography[J]. Materials Characterization,2020,166:1. [21] Kania H. The structure of coatings obtained in the Zn-31Al-3Mg bath on high-silicon steel[J]. Solid State Phenomena,2014,212:101. [22] Borrajo P R,Hedstrom P. Recent developments of crystallographic analysis methods in the scanning electron microscope for applications in metallurgy[J]. Critical Reviews in Solid State and Material Sciences,2017,43(2):1. [23] Van B R,Ribas G D,De Jeer L T H,et al. On the optimum resolution of transmission-electron back-scattered diffraction (t-EBSD)[J]. Ultra Microscopy,2016,160(1):256. [24] Trimby P W.Orientation mapping of nanostructured materials using transmission kikuchi diffraction in the scanning electron microscope[J]. Ultra Microscopy,2012,120(5):16. [25] Commenda C,Puhringer J. Microstructural characterization and quantification of Zn-Al-Mg surface coatings[J]. Materials Characterization,2010,61:943. [26] YU K C,LI J,LIU X. Microstructure of hot-dip galvanized Zn-Al-Mg alloy coating[J]. Journal of Shanghai Jiaotong University Science,2012,17(6):663. [27] Prabhat K R,Rout D,Satish K D,et al. Effect of Magnesium on corrosion behavior of hot-dip Zn-Al-Mg coating[J]. Journal of Materials Engineering and Performance,2021,30:4138. [28] Salgueiro A M,Allely C,Ogle K,et al. Corrosion mechanisms of Zn(Mg,Al) coated steel:2. The effect of Mg and Al alloying on the formation and properties of corrosion products in different electrolytes[J]. Corrosion Science,2015,90:482.