低压脉冲磁场凝固硅钢的热变形组织和行为

doi:10.13228/j.boyuan.issn0449-749x.20220504

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (4448 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为了细化硅钢铸锭组织,提高其加工性能,研究了低压脉冲磁场对硅钢凝固组织的影响规律,并对比了不同凝固组织的热变形行为和组织。研究结果表明,在硅钢的凝固过程中施加脉冲磁场,传统的柱状晶组织转变为等轴晶组织。随着磁场频率的增加,等轴晶比率(等轴晶面积/整体面积)先增加后降低,等轴晶晶粒尺寸先减小后增大。随着励磁电压增加,等轴晶比率增加,等轴晶晶粒尺寸不断增加,获得最佳脉冲磁场工艺参数,磁场频率为5 Hz,励磁电压为200 V。在该脉冲磁场工艺参数下,硅钢凝固组织中的等轴晶尺寸细化至无磁场作用时的1/2,等轴晶比率提高至100%。对无脉冲磁场的柱状晶组织和施加脉冲磁场(磁场频率为5 Hz,励磁电压为200 V)的等轴晶组织,进行了热压缩试验(温度为950 ℃,应变速率为0.01 s^-1和0.1 s^-1)和热轧试验(初轧温度1 100 ℃)。通过微观组织结果发现,无脉冲磁场作用的柱状晶凝固组织在热压缩过程中发生少量动态再结晶,组织中存在难以消除的变形晶粒,影响后续加工性能。脉冲磁场作用下等轴晶凝固组织在相同热压缩条件下获得细小均匀的再结晶组织,平均晶粒尺寸为670 μm。对比热轧板材组织和织构结果,同样发现脉冲磁场作用下的等轴晶凝固组织在热变形过程中更易发生动态再结晶,且轧制织构强度和板材各向异性更弱。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	郑策
	李应举
	陶文哲
	罗天骄
	杨院生

关键词 ：热变形, 低压脉冲磁场, 硅钢, 凝固组织, 再结晶

Abstract：In order to refine the microstructure of silicon steel ingot and improve its processability, the effect of low voltage pulsed magnetic field (LVPMF) on the solidification structure of silicon steel was investigated, and the hot deformation behavior and microstructure of different as-cast microstructures were compared. The fine grains are obtained by employing the low voltage pulsed magnetic field during the solidification of silicon steel. With the increase of frequency of LVPMF, the ratio of equiaxed grains (area of equiaxed grains to whole area) and average grain size of equiaxed grains was increased firstly and then decreased. In addition, the ratio and average grain size of equiaxed grains increased with the voltage of LVPMF. The average size equiaxed grain is refined to half of grains without LVPMF, and the ratio of equiaxed grains increased from 10% to 100% under optimal LVPMF parameter with frequency of 5 Hz and voltage of 200 V. Hot compression experiments (deformation temperature of 950 ℃, strain rate of 0.01 s^-1 and 0.1 s^-1) and hot rolling experiments (blooming temperature 1 100 ℃) were carried out for columnar grains solidified without LVPMF and equiaxed grains solidified with LVPMF (frequency of 5 Hz, voltage of 200 V). A small amount of recrystallization grains occurs and strip-shaped grains are formed in the samples solidified without LVPMF with columnar grains after hot compression. The strip-shaped grains are hard to eliminate and deteriorate processing performance of the alloy. The samples solidified with LVPMF with equiaxed grains can be fully recrystallized after hot compression. Therefore, fine recrystallization grains are acquired with average size of 670 μm. By comparing the microstructure and texture of hot-rolled sheets, it is found that the samples with LVPMF with equiaxed grains are more prone to recrystallization during hot rolling, resulting in weaker texture intensity and anisotropy.

Key words： hot deformation low voltage pulsed magnetic field silicon steel solidified microstructure recrystallization

收稿日期: 2022-07-29

引用本文:

郑策, 李应举, 陶文哲, 罗天骄, 杨院生. 低压脉冲磁场凝固硅钢的热变形组织和行为[J]. 钢铁, 2023, 58(2): 159-167. ZHENG Ce, LI Ying-ju, TAO Wen-zhe, LUO Tian-jiao, YANG Yuan-sheng. Hot deformation microstructure and behavior of silicon steel solidified under low voltage pulsed magnetic field[J]. Iron and Steel, 2023, 58(2): 159-167.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20220504 或 http://www.chinamet.cn/Jweb_gt/CN/Y2023/V58/I2/159

[1] 何忠志.电工钢[M].北京:冶金工业出版社,2002. (HE Zhong-zhi.Electrical steel[M].Beijing:Metallurgical Industry Press,2002.)
[2] 仇圣桃,项利,岳尔斌,等.薄板坯连铸连轧流程生产取向硅钢技术分析[J].钢铁.2008,43(9):1.(QIU Sheng-tao,XIANG Li,YUE Er-bin,et al. Technology analysis of producing grain oriented silicon steel by thin slab casting and rolling process [J]. Iron and Steel. 2008,43(9):1.)
[3] Nakada M,Shiohara Y,Flemings M C. Modification of solidification structures by pulse electric discharging[J]. ISIJ International,1990,30(1):27.
[4] ZI Bing-tao,BA Qi-xian,CUI Jian-zhong,et al. Study on axial changes of as-cast structures of Al-alloy sample treated by the novel SPMF technique[J]. Scripta Materialia,2000,43(4):377.
[5] 赵志龙,张蓉,刘林,等.强脉冲磁场中Al-Cu共晶定向凝固组织的演变[J].材料研究学报,2005,19(2):207.(ZHAO Zhi-long,ZHANG Rong,LIU Lin,et al. Evolvement of Al-Cu eutectic unidirectionally solidified morphology in high intensity pulsed magnetic field[J]. Chinese Journal of Materials Research,2005,19(2):207.)
[6] GAO Yu-lai,LI Qiu-shu,GONG Yong-yong,et al. Comparative study on structural transformation of low-melting pure Al and high-melting stainless steel under external pulsed magnetic field[J]. Materials Letters,2007,61(18):4011.
[7] WANG Bin,YANG Yuan-sheng,ZHOU Ji-xue,et al. Microstructure Refinement of an AZ91D Alloy Solidified With Pulsed Magnetic field[J].Transactions of Nonferrous Metals Society of China,2008(18):536.
[8] MA Xiao-ping,LI Ying-ju,YANG Yuan-sheng. Grain refinement effect of a pulsed magnetic field on as-cast superalloy K417[J]. Journal of Materials Research,2009,24(8):2670.
[9] ZHANG Lei,LI Wei,YAO Jun-ping,et al. Effects of pulsed magnetic field on microstructures and morphology of the primary phase in semisolid A356 Al slurry[J]. Materials Letters,2012,66(1):190.
[10] LI Ying-ju,TAO Wen-zhe,YANG Yuan-sheng. Grain refinement of Al-Cu alloy in low voltage pulsed magnetic field[J]. Journal of Materials Processing Technology,2012,212(4):903.
[11] FU Jun-wei,YANG Yuan-sheng. Formation of the solidified microstructure of Mg-Al-Zn alloy under a low-voltage pulsed magnetic field[J]. Journal of Materials Research,2011,26(14):1688.
[12] 华骏山,张永杰,王恩刚,等.脉冲磁场下电磁力特性研究:凝固实验[J].东北大学学报(自然科学版).2011,32(2):258.(HUA Jun-shan,ZHANG Yong-jie,WANG En-gang,et al. On the characteristics of pulsed electromagnetic force: solidification experiment[J]. Journal of Northeastern University(Natural Science),2011,32(2):258.)
[13] 滕跃飞,李应举,冯小辉,等. 脉冲磁场作用下矩形截面宽厚比对K4169高温合金晶粒细化的影响[J]. 金属学报,2015,51(7):844. (TENG Yue-fei,LI Ying-ju,FENG Xiao-hui,et al. Effect of rectangle aspect ratio of grain refinement of superalloy K4169 under pulsed magnetic field[J]. Acta Metallurgica Sinica,2015,51(7):844.)
[14] 张建伟,李应举,杨院生. 脉冲磁场对定向H13钢凝固组织的影响[J].材料研究学报,2017,31(10):721.(ZHANG Jian-wei,LI Ying-ju,YANG Yuan-sheng. Effect of applied pulsed magnetic field during directional solidification on solidification structure of H13 steel[J]. Chinese Journal of Materials Research,2017,31(10):721.)
[15] 冀焕明,罗天骄,杨院生. AZ80镁合金低压脉冲磁场半连续铸造过程的数值模拟和实验研究[J]. 中国有色金属学报,2017,27(3):468.(JI Huan-ming,LUO Tian-jiao,YANG Yuan-sheng. Numerical simulation and experimental research of low voltage pulsed magnetic field DC casting of AZ80 magnesium alloy[J]. Chinese Journal of Nonferrous Metals.,2017,27(3):468.)
[16] MA Xiao-ping,YANG Yuan-sheng,WANG Bin. Effect of pulsed magnetic field on superalloy melt[J]. International Journal of Heat and Mass Transfer,2009,52(23/24):5285.
[17] ZHANG Kui-liang,LI Ying-ju,YANG Yuan-sheng. Influence of the low voltage pulsed magnetic field on the columnar-to-equiaxed transition during directional solidification of superalloy K4169[J]. Journal of Materials Science and Technology,2020,48:9.
[18] 汪彬,杨院生,周吉学,等.脉冲磁场对Mg-Gd-Y-Zr合金凝固及力学性能的影响[J].稀有金属材料与工程,2009(38):519.(WANG Bin, YANG Yuan-sheng, ZHOU Ji-xue, et al. Effect of pulsed magnetic field on solidification and mechanical properties of Mg-Gd-Y-Zr alloy[J]. Rare Metal Materials and Engineering, 2009 (38):519.)
[19] 干勇,田志凌,董瀚,等.中国材料工程大典第2卷钢铁材料工程(上)[M].北京:化学工业出版社,2005.(GAN Yong, TIAN Zhi-ling, DONG Han, et al. China Material Engineering Ceremony. Volume 2 Steel Material Engineering (Part 1) [M]. Beijing: Chemical Industry Press, 2005.)
[20] Zhou L X,Baker T N.Effects of dynamic and metadynamic recrystallization on microstructures of wrought IN-718 due to hot deformation[J].Materials Science and Engineering A,1995(196):89.