七机架热连轧机组轧制温度综合优化技术

doi:10.13228/j.boyuan.issn0449-749x.20220573

摘要
图/表
参考文献
相关文章 (5)

全文: PDF (1593 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要热连轧轧制过程中的轧制温度会影响带钢变形抗力以及轧制力的大小,进而改变带钢的出口厚度以及出口板形分布,因此,当轧制温度设定不合理时,会导致带钢的出口厚度精度变低、出口板形质量变差。充分考虑到热连轧机组的设备特点及其轧制工艺特点,首先,通过对变形抗力模型、出口厚度模型、宽展量模型以及出口板形模型的研究,定量分析了轧制温度对变形抗力、出口厚度、带钢宽展量以及出口板形的影响效果及其影响过程。然后,针对由于轧制温度设定不合理而导致的出口板形质量较差的问题,以板形分布的极值差值程度以及波动程度为约束条件建立了带钢板形横向控制目标函数与纵向控制目标函数,进而建立了带钢板形综合控制目标函数,针对由于轧制温度设定不合理而导致的出口厚度精度较低的问题,以出口厚度偏差的标准差以及出口厚度偏差的平均值为约束条件建立了带钢厚度偏差综合控制目标函数,并在此基础上以出口板形最优以及出口厚度偏差最小为目标,以7个机架的极限轧制力、宽展量以及轧制温度变化范围为约束条件建立了七机架热连轧机组轧制温度综合优化设定目标函数,实现了七机架热连轧机组轧制温度设定值的综合优化,将该优化技术应用到了国内某热连轧机组的带钢生产中后使得带钢出口板形质量得到改善,出口厚度控制精度得到提高。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	李学通
	张燕东
	尹宝良
	李子正
	邝霜
	王瑞

关键词 ：热连轧机组, 轧制温度, 综合优化, 出口板形, 出口厚度

Abstract：The rolling temperature during hot rolling will affect the deformation resistance and rolling force of the strip steel. Then the exit thickness and the exit shape distribution of the strip steel are changed. Therefore,the outlet thickness accuracy of strip steel will become lower and the outlet shape quality will become worse when the rolling temperature is set unreasonably. Fully consider the equipment characteristics and rolling process characteristics of the hot strip mill. Firstly,deformation resistance model and outlet thickness model and width model and outlet shape model are studied to solve these problems. The influence of rolling temperature on deformation resistance and exit thickness and strip width and exit shape is analyzed quantitatively. Aiming at the problem of poor exit shape quality caused by unreasonable rolling temperature setting. The horizontal control objective function and the longitudinal control objective function of strip shape are established with the extreme difference degree and fluctuation degree of strip shape distribution as constraints. And then,the shape synthesis control objective function is established. Aiming at the problem of low outlet thickness accuracy caused by unreasonable rolling temperature setting. Taking the standard deviation of the exit thickness deviation and the average value of the exit thickness deviation as constraints,the comprehensive control objective function of the strip thickness deviation was established. The comprehensive control objective function of the strip thickness deviation was established taking the standard deviation of the exit thickness deviation and the average value of the exit thickness deviation as constraints. On this basis,the best shape of the exit and the minimum deviation of the exit thickness are set as the goals. The limit rolling force and the spread and the range of rolling temperature of the seven stands are taken as constraints. The objective function of rolling temperature optimization for seven stand hot strip mill was established. The comprehensive optimization of the rolling temperature setting value of the seven-stand hot strip mill is realized. After the optimization technology is applied to the strip production of a domestic hot strip mill,the quality of strip shape at the exit is improved,and the accuracy of strip thickness control at the exit is improved.

Key words： hot tandem mill rolling temperature comprehensive optimization outlet shape outlet thickness

收稿日期: 2022-09-06

引用本文:

李学通, 张燕东, 尹宝良, 李子正, 邝霜, 王瑞. 七机架热连轧机组轧制温度综合优化技术[J]. 钢铁, 2023, 58(3): 104-110. LI Xue-tong, ZHANG Yan-dong, YIN Bao-liang, LI Zi-zheng, KUANG Shuang, WANG Rui. Comprehensive optimization technology of rolling temperature for seven stand hot strip mill[J]. Iron and Steel, 2023, 58(3): 104-110.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20220573 或 http://www.chinamet.cn/Jweb_gt/CN/Y2023/V58/I3/104

[1] 赵燕青,齐建军,孙力,等. 终轧温度对高锰奥氏体低温钢组织和力学性能的影响[J]. 河北冶金,2022(6):14.(ZHAO Yan-qing,QI Jian-jun,SUN Li,et al Effect of finishing rolling temperature on microstructure and mechanical properties of high manganese austenitic low temperature steel[J]. Hebei Metallurgy,2022(6):14.)
[2] 魏宝民,王孝建,崔熙颖,等. 热轧温度波动对冷轧变形抗力的影响模型[J]. 塑性工程学报,2022,29(1):162.(WEI Bao-min,WANG Xiao-jian,CUI Xi-ying,et al. Influence model of hot rolling temperature fluctuation on cold rolling deformation resistance[J]. Chinese Journal of Plastic Engineering,2022,29(1):162.)
[3] 才磊. GF08Al热轧窄带钢轧制过程温度控制的研究[D]. 沈阳:东北大学,2018.(CAI Lei. Study on the Temperature Control in the Rolling Process of GF08Al Hot Rolled Narrow Strip Steel[D]. Shenyang:Northeast University,2018.)
[4] 荆丰伟,冯莹,陈兆宇,等. 数据驱动的热轧带钢头部终轧温度预计算优化[J]. 钢铁研究学报,2022,34(7):655.(JING Feng-wei,FENG Ying,CHEN Zhao-yu,et al. Data driven pre calculation optimization of hot strip head finishing temperature[J]. Journal of Iron and Steel Research,2022,34(7):655.)
[5] 吴腾,万湛勋,杨玉佳,等. 终轧温度对超高强热轧双相钢组织性能的影响[J]. 钢铁研究学报,2021,33(6):515.(WU Teng, WAN Zhan-xun, YANG Yu-jia, et al. Effect of finishing rolling temperature on microstructure and properties of ultra-high strength hot rolled dual phase steel[J]. Journal of Iron and Steel Research, 2021,33 (6): 515.)
[6] 易成新,李维刚,吕立华,等. 基于RF-LSTM的热连轧板坯粗轧出口温度预报[J]. 钢铁研究学报,2021,33(9):952.(YI Cheng-xin,LI Wei-gang,LÜ Li-hua,et al Prediction of rough rolling exit temperature of hot continuous rolling slab based on RF-LSTM[J]. Journal of Iron and Steel Research,2021,33(9):952.)
[7] 陈建超,庞洪轩,温超,等. 终轧温度对加Ti低合金Q355B钢板组织性能的影响[J]. 中国冶金,2021,31(10):30.(CHEN Jian-chao, PANG Hong-xuan, WEN Chao, et al. Effect of finishing rolling temperature on microstructure and properties of Ti added low alloy Q355B steel plate[J]. China Metallurgy, 2021,31 (10): 30.)
[8] 彭良贵,周政,张敏,等. 热轧薄带目标终冷温度差异化设定策略及应用[J]. 轧钢,2016,33(5):56.(PENG Liang-gui, ZHOU Zheng, ZHANG Min, et al. Target final cooling temperature difference setting strategy and application of hot rolled thin strip[J]. Steel Rolling, 2016,33 (5): 56.)
[9] 徐耀,沈际海. 热轧带钢三维温度计算与应用[J]. 宝钢技术,2020(2):57.(XU Yao,SHEN Ji-hai. Three-dimensional temperature calculation and application of hot-rolled strip steel[J]. Baosteel Technology,2020(2):57.)
[10] 张建雷,张田,杜平,等. 厚板厚向温度分布对热轧过程金属变形的影响[J]. 轧钢,2020,37(6):1.(ZHANG Jian-lei, ZHANG Tian, DU Ping, et al. Effect of temperature distribution along thickness direction of thick plate on metal deformation during hot rolling[J]. Steel Rolling, 2020, 37 (6): 1.)
[11] 李维刚,冯宁,王慎德,等. 热轧相变过程变形抗力模型研究与开发[J]. 钢铁,2017,52(6):61.(LI Wei-gang,FENG Ning,WANG Shen-de,et al. Research and development of deformation resistance model during hot rolling transformation process[J]. Iron and Steel,2017,52(6):61.)
[12] 孙一康. 带钢热连轧数学模型基础[M]. 北京:冶金工业出版社,1979.(SUN Yi-kang. Mathematical Model Basis for Hot Strip Rolling[M]. Beijing:Metallurgical Industry Press,1979.)
[13] 连家创,刘宏民. 板厚板形控制[M]. 北京:兵器工业出版社,1996.(LIAN Jia-chuang,LIU Hong-min. Plate Thickness and Shape Control[M].Beijing:Ordnance Industry Press,1996.)
[14] 靳皓越,孙杰,魏臻,等. 基于有限元法的拉伸弯曲矫直过程板形控制分析[J]. 钢铁,2022,57(6):100.(JIN Hao-yue, SUN Jie, WEI Zhen, et al. Shape control analysis of tension bending straightening process based on finite element method[J]. Iron and Steel, 2022,57 (6): 100.)
[15] 李耀辉,李定国. 马钢 CSP 热轧 PFC 板形模型的分析与应用[J]. 中国冶金,2015,25(11):40.(LI Yao-hui, LI Ding-guo. Analysis and application of PFC shape model for CSP hot rolling at Masteel[J]. China Metallurgy, 2015,25(11): 40.)
[16] 李伯群,范璇,李伟红,等. 板形设定模型参数优化与控制技术应用[J]. 钢铁,2019,54(2):41.(LI Bo-qun, FAN Xuan, LI Wei-hong, et al. Shape setting model parameter optimization and control technology application[J]. Iron and Steel, 2019, 54 (2): 41.)