304系不锈钢冶金过程硬质夹杂物形成机理分析

doi:10.13228/j.boyuan.issn0449-749x.20220547

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (4396 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要 304不锈钢由于具有优异的耐蚀性、加工性能被广泛应用,而钢中硬质夹杂物对冷板表面质量影响较大。为了明晰304不锈钢中硬质夹杂物的形成机理,通过工业生产取样,利用自动扫描电镜ASPEX及统计方法,研究了304不锈钢冶炼过程中全氧含量、各类夹杂物的变化规律。研究结果表明,从AOD出钢到铸坯过程中,随着底吹搅拌的进行,钢中T[O]含量不断降低,T[O]质量分数由0.008 8%降低至0.002 5%。AOD出钢和LF出站夹杂物主要类型为硅酸盐,并含由少量复合型硅酸盐和镁铝尖晶石夹杂物,LF出站至铸坯,夹杂物的成分发生了部分转变,夹杂物中SiO₂含量减少,Al₂O₃含量升高。从AOD出钢至中间包,钢液中硬质夹杂物镁铝尖晶石和Al₂O₃很少,但从中间包到铸坯其比例显著增加,镁铝尖晶石夹杂物的比例增加了28%,钢-渣反应脱氧产物中的复合型硅酸盐夹杂物的比例也明显增加,而脱氧剂脱氧产物SiO₂和钢-渣反应脱氧产物中SiO₂-Al₂O₃的比例显著降低。铸坯中尺寸不大于10 μm的夹杂物所占比例较大的分别为复合型硅酸盐、镁铝尖晶石和SiO₂夹杂物。利用热力学软件计算了不同组分的CaO-SiO₂-Al₂O₃-MgO熔体随温度降低的相变行为,熔体在温度降低过程中会析出镁铝尖晶石高熔点相,且随着熔体中MgO和Al₂O₃含量的增加,镁铝尖晶石析出的温度显著升高,更易析出镁铝尖晶石。硬质夹杂物主要是由钢-渣脱氧产物硅铝酸盐和复合型硅酸盐等在连铸凝固过程中随着温度降低凝固析出形成。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	翟俊
	王伟
	郎炜昀

关键词 ： 304不锈钢, 硬质夹杂物, 镁铝尖晶石, 表面质量, 脱氧产物

Abstract：304 stainless steel is widely used due to the excellent corrosion resistance and processing performance, while the hard inclusions in the steel have a great influence on the surface quality of the cold plate. The variation law of the size and quantity of various inclusions in the smelting process of 304 stainless steel was investigated in order to clarify the formation mechanism of hard inclusions in 304 stainless steel, through sampling in industrial production and using automatic scanning electron microscope ASPEX and statistical methods. The results show that the total oxygen content of steel casting decreases continuously with the bottom blowing and stirring, and the mass percent of T[O] decreases from 0.008 8% to 0.002 5% in the process from AOD steel production to casting. The main types inclusions at the end of AOD and LF are silicate, and contain a small amount of compound silicate and a small amount of magnesium aluminum spinel inclusions. From the end of LF to slab, The composition of the inclusions has undergone a partial transformation, the content of SiO₂ in the inclusions decreases, and the content of Al₂O₃ increases. From AOD to tundish, the hard inclusions of magnesium-aluminum spinel and Al₂O₃ in molten steel are very few, while the proportion increases significantly from tundish to slab, the ratio of magnesium-aluminum spinel increases by 28%, and the percentage of compound silicate inclusions in the deoxidation products of steel-slag reaction also increases significantly. However, the proportion of SiO₂-Al₂O₃in the deoxidized product of deoxidizer and the deoxidized product of steel-slag reaction decreased significantly. The largest proportions are composite silicate, magnesium-aluminum spinel and SiO₂ inclusions among the types of inclusions with a size of ≥10 μm in the slab. The phase transition behavior of CaO-SiO₂-Al₂O₃-MgO melts with different compositions was calculated by thermodynamic software. The melt will precipitate a high melting point phase of MgO-Al₂O₃when the temperature decreases, and the precipitation temperature of magnesia-aluminum spinel increased significantly and the magnesia-aluminum spinel phase was more easily precipitated with increase of the content of MgO and Al₂O₃ in the melt. The hard inclusions are mainly formed by the deoxidation products silicaluminate and composite silicate during the solidification process of continuous casting with the decreasing of temperature.

Key words： 304 stainless steel hard inclusions magnesium aluminum spinel surface quality deoxidation products

收稿日期: 2022-08-26

引用本文:

翟俊, 王伟, 郎炜昀. 304系不锈钢冶金过程硬质夹杂物形成机理分析[J]. 钢铁, 2023, 58(4): 39-47. ZHAI Jun, WANG Wei, LANG Wei-yun. Analysis of formation mechanism of hard inclusions during metallurgical process of 304 stainless steel[J]. Iron and Steel, 2023, 58(4): 39-47.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20220547 或 http://www.chinamet.cn/Jweb_gt/CN/Y2023/V58/I4/39

[1] 罗宏,龚敏.奥氏体不锈钢的晶间腐蚀[J]. 腐蚀科学与防护技术,2006,18(5):357. (LUO Hong,GONG Ming. On intergranular corrosion of austenitic stainless steel[J]. Corrosion Science and Protection Technology, 2006,18(5):357.)
[2] 林玉珍,杨德均.腐蚀和腐蚀控制原理[M]. 北京: 中国石化出版社, 2007. (LIN Yu-zhen, YANG De-Jun. Principles of Corrosion and Corrosion Control[M]. Beijing: China Petrochemical Press,2007.)
[3] 高文芳.冷轧薄板表面缺陷研究[J].炼钢,2006,22(3):22.(GAO Wen-fang. Research on surface defects of cold rolled sheet[J]. Steelmaking, 2006,22(3):22.)
[4] 马骏, 陈兴润.304不锈钢2B板表面线磷缺陷改进实践[J]. 中国冶金, 2015, 25(6): 54. (MA Jun, CHEN Xing-run. Improvement practice for the line scales on surface of 304 stainless steel 2B plate[J]. China Metallurgy, 2015,25(6):54.)
[5] 苑鹏,李海波,陈斌,等.汽车钢板表面线状缺陷表面控制技术[J].钢铁研究学报,2017,29(10):800. (YUAN Peng, LI Hai-bo, CHEN Bin, et al. Control technology of surface sliver defects for antomobile steel sheets[J]. Journal of Iron and Steel Research,2017,29(10):800.)
[6] 高文芳,颜正国,宋平,等.荫罩框架钢冷轧板边部线状缺陷研究[J].炼钢,2003,19(1):31. (GAO Wen-fang, YAN Zheng-guo, SUN Ping, et al. Research on sliver defects along the edges of shadow mask and chassis steel strip[J]. Steelmaking, 2003,19(1):31.)
[7] 张立峰, 王新华. 连铸钢中的夹杂物[J]. 山东冶金, 2005, 27(2): 1.(ZHANG Li-feng, WANG Xin-hua. Inclusions in continuous cast steel[J]. Shandong Metallurgy, 2005, 27(2):1.)
[8] 海超, 左海霞. 夹杂物引起冷轧板表面缺陷的成因与控制[J]. 本钢技术, 2013(5): 25.(HAI Chao, ZUO Hai-xia. Causes and control of surface defects of cold rolled plates caused by inclusions[J]. Benxi Steel Technology, 2013(5):25.)
[9] Sudesh T L, Wijesinghe L, Daniel J B. Real time pit initiation studies on stainless steels: The effect of sulphide inclusions[J]. Corrosion Science,2007,49(4): 1755.
[10] Okuyama Q, Yamaguchi K, Takeuchi S, et al. Effect of slag composition on the kinetics of formation of Al₂O₃-MgO inclusions in aluminum killed ferritic stainless steel[J].ISIJ International, 2000, 40(2): 121.
[11] Krawiec H, Vignal V, Heintz O, et al. Dissolution of chromium-enriched inclusions and pitting corrosion of resulfurized stainless steels[J]. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 2006, 37(5): 1541.
[12] 王国伟,郑万,陈小龙,等.连铸连轧卷板边部线状缺陷的形成机制[J].钢铁研究学报,2021,33(1):64.(WANG Guo-wei,ZHENG Wan,CHEN Xiao-long,et al. Formation mechanism of linear defects on edge of continuous casting and rolling coil[J]. Journal of Iron and Steel Research,2021,33(1):64.)
[13] Genzano C,Madias J,Dalmaso D,et al.Elimination of surface defect in cold-rolled exrat low carbon steel[J].Iron and Steel Maker,2002,29(6):23.
[14] 顾武安.攀钢冷轧板条形缺陷的研究[D].北京:北京科技大学,2001.(GU Wu-an. Study on Strip Defect of Cold Rolled Sheet at Pan Steel[D]. Beijing: University of Science and Technology Beijing,2001.)
[15] 曾溢彬,包燕平,赵家七,等. 硅锰脱氧55SiCr弹簧钢种镁铝尖晶石的形成及演变[J]. 钢铁, 2022, 57(8): 69.(ZENG Yi-bin,BAO Yan-ping,ZHAO Jia-qi,et al.Formation and evolution of magnesia-alumina spinel in Si-Mn deoxidized 55SiCr spring steel[J]. Iron and Steel, 2022, 57(8): 69.)
[16] 肖微,包燕平,王敏,等. 非铝脱氧GCr15轴承钢夹杂物的演变与控制[J]. 钢铁, 2021, 56(1): 37.(XIAO Wei,BAO Yan-ping,WANG Min,et al. Inclusions evolution and control of non-aluminum deoxidized GCr15 bearing steel[J]. Iron and Steel, 2021, 56(1): 37.)
[17] 梁雪,杨树峰,李京社,等. 高品质含钛焊丝钢生产过程中夹杂物的行为演变[J]. 中国冶金, 2020, 30(2): 19.(LIANG Xue,YANG Shu-feng,LI Jing-she,et al. Evolution behavior of inclusions during production of high-quality titanium-bearing welding wire steel[J]. China Metallurgy, 2020, 30(2):19.)
[18] 王海生. 304不锈钢线鳞缺陷成因分析及改进措施[J]. 世界钢铁, 2014, 14(5): 31.(WANG Hai-sheng. Causes analysis and improving measures of sliver defect in 304 stainless steel[J]. World Iron and Steel, 2014,14(5),31.)
[19] Sidor Y, Dzubinsky M K Ovac. Charaterization of microstructures in non-orenled electrical steels utilizing weighted sum of elementary[J]. Czechoslovak Journal of Phusics,2004,54(12):105.
[20] 茅卫东. SUS304不锈钢表面抛光缺陷原因分析及改进措施[J]. 上海金属,2011,33(2): 58. (MAO Wei-dong. Analysis of surface polish defects on SUS304 stainless steel and the improvement measures[J]. Shanghai Metals, 2011,33(2):58.)
[21] Mizuno K, Todoroki H, Noda M, et al. Effects of Al and Ca in ferrosilicon alloys for deoxidation on inclusion composition in type 304 stainless steel[J]. Iron Steelmaker, 2001, 28(8): 93.
[22] Okuyama G, Yamaguchi K, Takeuchi S, et al. Effect of slag composition on the kinetics of formation of A1₂O₃-MgO inclusions in aluminum killed ferritic stainless steel[J]. ISIJ International, 2000, 40(2): 121.
[23] 陈云华, 张平, 卢柳林. 非金属夹杂物对钢制零件产品质量的影响[J]. 理化检验——物理分册, 2005, 41(11): 556. (CHEN Yun-hua, ZHANG Pin, LU Liu-ling. The effect of nonmetallic inclusion in the steel on product quality[J]. Physical Testing and Chemical Analysis(Part: A Physcial Testing), 2005, 41(11): 556.