GH2132合金混晶条带组织分析及其对力学性能影响

doi:10.13228/j.boyuan.issn0449-749x.20220036

Abstract
Figure/Table
References
Related Citation (7)

Download: PDF (8056 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Band-typed mixed grain structure defect was an important reason affecting the stability of microstructure and properties of GH2132 alloy, so the band-typed mixed grain structure with cold drawn bars were experimentally studied in this article. By means of metallography, EPMA, EBSD and TEM, combined with thermodynamic equilibrium phase diagram and hardness test, the main causes of band-typed mixed grain structure were revealed, as well as the analysis of its internal microstructure and the effect on microhardness. The results show that the grain size of fine grain zone in band-typed mixed grain structure is generally less than 10 μm, while the maximum grain size in coarse grain zone is over 60 μm. It is analyzed that element segregation and cold drawing deformation are the causes for the difference of grain size, and the forming of band-typed mixed grain structure. Ti, Mo, C and B elements in the as-cast structure of the alloy show positive segregation, among which the segregation of C and Ti element is greater, leading to the precipitation of MC and M₃B₂ phases between dendrites, which will finally appear between the grain boundaries in austenite. The solute enrichment between grain boundaries not only plays a pinning role to prevent the grain growth during recrystallization, but also reduces the migration rate of grain boundary through solute drag, which hinders the grain boundary deformation. Finally, the solute enrichment area forms a fine grain zone, with the depleted region forming a coarse grain region. Both display band-typed mixed grain structure along the cold drawing direction. In addition, due to the different crystal orientation, the actual strains of grain deformation under the same drawing force are not consistent during cold drawing deforming, which will also aggravate the mixed grain phenomenon. The microscopic observation shows that after cold deformation, the deformation of fine grain region is more uniform compared with the coarse grain region, and the average dislocation density in the microstructure is higher. Annealing twins and deformation twins are observed in the mixed grain region, while the twin density in the fine crystal region is higher. To sum up, the different numbers of grain boundaries, with the change of dislocation density and the gradient structure of twin distribution finally lead to the microhardness gradient in the mixed grain region, where the hardness of fine grain region is significantly higher.

Key words： GH2132 alloy band-typed mixed grain structure elemental segregation cold drawing deformation hardness gradient

Received: 12 January 2022

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LIU Ji-meng
	HUANG Shuo
	ZHANG Xiao-min
	DUAN Ran
	LIU Kang-kang
	QIN He-yong

Cite this article:

LIU Ji-meng,HUANG Shuo,ZHANG Xiao-min等. Microstructure analysis of GH2132 alloy band-typed mixed grain structure and its effect on mechanical properties[J]. Iron and Steel, 2022, 57(6): 110-119.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20220036 OR http://www.chinamet.cn/Jweb_gt/EN/Y2022/V57/I6/110

[1] 冯光勇, 赵峰. 高强度 GH2132 合金力学性能影响因素[J]. 航空发动机, 2020, 46(3): 94. (FENG Guang-yong, ZHAO Feng. Effect factors analysis of the bolts mechanical properties of high strength GH2132 alloy[J]. Aeroengine, 2020, 46(3): 94.)
[2] Esfandiari M, Dong H. Improving the surface properties of A286 precipitation-hardening stainless steel by low-temperature plasma nitriding[J]. Surface and Coatings Technology, 2007, 201(14): 6189.
[3] LIU S C, GAO Y, LIN Z L, et al. Microstructure and properties after deformation and aging process of A286 superalloy[J]. Rare Metals, 2019, 38(9): 864.
[4] WEI L, ZHAO H, SUN Y, et al. Microstructure evolution and stress rupture properties of A286 superalloy in the 600 to 750 ℃ temperature range[J]. Materials Research Express, 2021, 8(2): 026521.
[5] Kobayashi K, Yamaguchi K, Hayakawa M, et al. High-temperature fatigue properties of austenitic superalloys 718, A286 and 304L[J]. International Journal of Fatigue, 2008, 30(10/11): 1978.
[6] 柳思成, 许彦伟, 殷小健, 等. 形变量及时效制度对A286高温合金组织和性能的影响[J]. 金属热处理, 2019, 44(5): 167. (LIU Si-cheng, XU Yan-wei, YIN Xiao-jian, et al. Effects of deformation and aging on microstructure and properties of A286 superalloy[J]. Heat Treatment of Metals, 2019, 44(5): 167.)
[7] 秦鹤勇, 裴丙红, 董建, 等. 高强度GH2132合金棒材冷拔工艺的研究[J]. 钢铁研究学报, 2010, 22(9): 48. (QIN He-yong, PEI Bing-hong, DONG Jian, et al. Study on cold drawing process of high-strength alloy GH2132[J]. Journal of Iron and Steel Research, 2010, 22(9): 48.)
[8] 张立新, 孙奇, 于湃, 等. 优质GH2132合金叶片锻件屈服强度不合格的原因[J]. 物理测试, 2013, 31(4): 49. (ZHANG Li-xin, SUN Qi, YU Pai, et al. Reasons for unqualified yield strength of high quality GH2132 alloy blade forgings[J]. Physics Examination and Testing, 2013, 31(4): 49.)
[9] 吕晶晶, 于广娜, 宋金贵. 原始晶粒尺寸和锻后变形量对GH2132合金晶粒度的影响[J]. 金属热处理, 2017, 42(12): 48. (LÜ Jing-jing, YU Guang-na, SONG Jin-gui. Effects of original grain size and deformation amount after forging on the grain size of GH2132 alloy[J]. Heat Treatment of Metals, 2017, 42(12): 48.)
[10] 许永春, 董新燕, 朱玲玲, 等. A286 螺栓晶粒异常长大原因分析[J]. 金属加工: 热加工, 2015(23): 74. (XU Yong-chun, DONG Xin-yan, ZHU Ling-ling, et al. Cause analysis of abnormal grain growth in A286 bolt[J]. Heat Treatment: Hot Treatment, 2015(23): 74.)
[11] 郭慧敏, 徐敬宇, 张哲爽, 等. A286 螺栓杆部粗晶问题的分析与处理[J]. 科技创新与应用, 2016(24): 154. (GUO Hui-min, XU Jing-yu, ZHANG Zhe-shuang, et al. Analysis and treatment of coarse grain in A286 bolt rod[J]. Scientific and Technological Innovation and Application, 2016(24): 154.)
[12] 杨飞飞, 张忠铧, 刘华松, 等. 高强度油井管用钢带状偏析及其条带型混晶现象研究[J]. 钢铁研究学报, 2021, 33(9): 979. (YANG Fei-fei, ZHANG Zhong-ye, LIU Hua-song, et al. Banded segregation and its related band-typed mixed grain structure in high strength oil well pipe steel[J]. Journal of Iron and Steel Research, 2021, 33(9): 979.)
[13] 李博, 杨飞飞, 刘华松, 等. 凝固组织对高强耐蚀管带状缺陷的影响[J]. 钢铁, 2020, 55(3): 87. (LI Bo, YANG Fei-fei, LIU Hua-song, et al. Effect of solidification structure on banded defects of high strength corrosion resistant tubes[J]. Iron and Steel, 2020, 55(3): 87.)
[14] Frisk R, Andersson N Å I, Rogberg B. Cast structure in Alloy A286, an iron-nickel based superalloy[J]. Metals, 2019, 9(6): 711.
[15] 谷雨, 杨树峰, 赵朋, 等. 镍基高温合金GH4738的凝固偏析和碳化物析出行为[J]. 中国冶金, 2021, 31(7): 13. (GU Yu, YANG Shu-feng, ZHAO Peng, et al. Solidification segregation and carbide precipitation behavior of nickel-based superalloy GH4738[J]. China Metallurgy, 2021, 31(7): 13.)
[16] 杨浩笛, 周扬, 赖宇, 等. 718Plus合金铸锭的元素偏析及均匀化工艺[J]. 材料热处理学报, 2021, 42(8): 69. (YANG Hao-di, ZHOU Yang, LAI Yu, et al. Element segregation and homogenization process of 718Plus alloy ingot[J]. Transactions of Materials and Heat Treatment, 2021, 42(8): 69.)
[17] 王迪, 杨树峰, 曲敬龙, 等. GH4169电渣重熔铸锭表层夹杂物分布规律[J]. 钢铁, 2021, 56(2): 155. (WANG Di, YANG Shu-feng, QU Jing-long, et al. Distribution of inclusions on surface of GH4169 ESR ingot[J]. Iron and Steel, 2021, 56(2): 155.)
[18] 吴宏辉, 周笑靥, 李博, 等. C晶界偏析对α-Fe 纳米晶高温力学性能的影响[J]. 钢铁研究学报, 2021, 33(4): 315. (WU Hong-hui, ZHOU Xiao-ye, LI Bo, et al. Influence of C grain boundary segregation on high temperature mechanical properties of nanograined α-Fe[J]. Journal of Iron and Steel Research, 2021, 33(4): 315.)
[19] Cutler E R, Wasson A J, Fuchs G E. Effect of minor alloying additions on the carbide morphology in a single crystal Ni-base superalloy[J]. Scripta Materialia, 2008, 58(2):146.
[20] 柯志刚, 朱丽慧, 周任远, 等. 钼对S30432耐热钢组织和性能的影响[J]. 钢铁, 2020, 55(7): 92. (KE Zhi-gang, ZHU Li-hui, ZHOU Ren-yuan, et al. Effect of Mo on microstructure and properties of S30432 heat-resistant steel[J]. Iron and Steel, 2020, 55(7): 92.)
[21] 王炜, 熊力, 朱航宇, 等. B在钢中的偏析及SS400含硼钢的重熔现象[J]. 钢铁研究学报, 2015, 27(12): 36. (WANG Wei, XIONG Li, ZHU Hang-yu, et al. Segregation of B in steel and remelting phenomenon after solidification of SS400 B-bearing steel[J]. Journal of Iron and Steel Research, 2015, 27(12): 36.)
[22] 王晓娟, 刘林, 赵新宝, 等. 添加碳和硼改善第三代镍基定向凝固高温合金的显微组织和偏析行为[J]. 材料导报, 2019, 33(20): 3452. (WANG Xiao-juan, LIU Lin, ZHAO Xin-bao, et al. Improvement of microstructures and segregation behavior of the third generation nickel-based directionally solidified superalloys by carbon and boron additions[J]. Materials Reports, 2019, 33(20): 3452.)
[23] Miyamoto G, Yokoyama K, Furuhara T. Quantitative analysis of Mo solute drag effect on ferrite and bainite transformations in Fe-0.4C-0.5Mo alloy[J]. Acta Materialia, 2019, 177: 187.
[24] 杨春雷, 徐红, 曾庆辉, 等. 304 奥氏体不锈钢冷拉拔过程中的微观组织不均匀性[J]. 材料热处理学报, 2019, 40(11): 159. (YANG Chun-lei, XU Hong, ZENG Qing-hui, et al. Microstructure inhomogeneous of 304 austenitic stainless steel during cold drawing[J]. Transactions of Materials and Heat Treatment, 2019, 40(11): 159.)
[25] 王露娟, 宋克兴, 王青, 等. 拉拔变形对不同直径纯铜线材组织性能的影响[J]. 河南科技大学学报(自然科学版), 2013, 34(3): 14. (WANG Lu-juan, SONG Ke-xing, WANG Qing, et al. Effect of drawing deformation on microstructure and properties for pure copper wire with different diameters[J]. Journal of Henan University of Science and Technology(Natural Science), 2013, 34(3): 14.)
[26] 李周选, 陈庆吟, 侯嘉鹏, 等. 拉拔变形量对Al-Mg-Si合金线微观组织和强度的影响[J]. 材料热处理学报, 2021, 42(1): 75. (LI Zhou-xuan, CHEN Qing-yin, HOU Jia-peng, et al. Effect of drawing deformation on microstructure and strength of Al-Mg-Si alloy wire[J]. Transactions of Materials and Heat Treatment, 2021, 42(1): 75.)
[27] Beyerlein I J,Tóth L S. Texture evolution in equal-channel angular extrusion[J]. Progress in Materials Science, 2009, 54(4): 427.
[28] MA X, CHEN J, WANG X, et al. Microstructure and mechanical properties of cold drawing CoCrFeMnNi high entropy alloy[J]. Journal of Alloys and Compounds, 2019, 795: 45.
[29] 张雪薇, 李超, 罗胜年. 晶粒取向和晶界对双晶铜变形的影响[J]. 实验力学, 2019, 34(3): 406. (ZHANG Xue-wei, LI Chao, LUO Sheng-nian. On the effect of grain orientation and grain boundary on the deformation of bicrystal copper[J]. Journal of Experimental Mechanics, 2019, 34(3):406.)
[30] CHEN C R, LI S X, WANG Z G. Characteristics of strain and resolved shear stress in a bicrystal with the grain boundary perpendicular to the tensile axis[J]. Materials Science and Engineering: A, 1998, 247(1/2): 15.
[31] 顾佳卿, 赵伟峰, 张志霞. EBSD 技术在不锈钢研究中的应用[J]. 宝钢技术, 2014(3): 63. (GU Jia-qing, ZHAO Wei-feng, ZHANG Zhi-xia. Application of EBSD analysis technology in stainless steel research[J]. Baosteel Technology, 2014(3): 63.)
[32] 唐超, 程世君, 曲敬龙, 等. 混晶组织对GH4720Li合金高温力学性能的影响[J].稀有金属材料与工程, 2021, 50(9): 3280. (TANG Chao, CHENG Shi-jun, QU Jing-long, et al. Effects of mixed-grain microstructure on high temperature mechanical properties of GH4720Li alloy[J]. Rare Metal Materials and Engineering, 2021, 50(9), 3280.)
[33] ZHANG Y, TAO N R, LU K. Effects of stacking fault energy, strain rate and temperature on microstructure and strength of nanostructured Cu-Al alloys subjected to plastic deformation[J]. Acta Materialia, 2011, 59(15): 6048.
[34] Cottrell A H, Bilby B A. A mechanism for the growth of deformation twins in crystals[J]. Philosophical Magazine, 1951, 42(329): 573.
[35] Remy L. The interaction between slip and twinning systems and the influence of twinning on the mechanical behaviour of FCC metals and alloys[J]. Metallurgical and Materials Transactions A, 1981, 12(3): 387.
[36] 张哲峰, 邵琛玮, 王斌, 等. 孪生诱发塑性钢拉伸与疲劳性能及变形机制[J]. 金属学报, 2020, 56(4): 476. (ZHANG Zhe-feng, SHAO Chen-wei, WANG Bin, et al. Tensile and fatigue properties and deformation mechanisms of twinning-induced plasticity steels[J]. Acta Metallurgic Sinica, 2020, 56(4): 476.)
[37] PANG Q, XU M, MI Z, et al. Microstructure evolution of ultra-high-strength twinning-induced plasticity (TWIP) steel under dynamic loading[J]. Journal of Iron and Steel Research, International, 2021, 28(1): 66.
[38] Hwang J K. Effect of grain size on tensile and wire drawing behaviors in twinning-induced plasticity steel[J]. Materials Science and Engineering: A, 2020, 772: 138709.
[39] LIU W H, WU Y, HE J Y, et al. Grain growth and the Hall-Petch relationship in a high-entropy FeCrNiCoMn alloy[J]. Scripta Materialia, 2013, 68(7): 526.
[40] 胡赓祥, 蔡珣, 戎咏华. 材料科学基础[M]. 上海: 上海交通大学出版社, 2010.(HU Geng-xiang, CAI Xun, RONG Yong-hua. Fundamentals of Materials Science[M]. Shanghai: Shanghai Jiao Tong University Press, 2010.)