连退炉用U型辐射管内无焰燃烧的数值模拟

doi:10.13228/j.boyuan.issn0449-749x.20210409

Abstract
Figure/Table
References
Related Citation (6)

Download: PDF (2698 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract In order to ensure that the heated workpiece is evenly heated without affecting its surface quality,the metallurgical industry generally uses radiant tubes to indirectly heat the workpiece. But at the same time,due to the limited combustion space in the radiant tube,it is easy to produce a local high temperature zone,which will affect the quality of the heated product,and the high temperature will cause a large amount of NO_x to be generated. In addition,the thermal stress generated by the large wall temperature difference will cause the tube wall damaged by creep,shortening its service life. Therefore,in order to optimize the performance of the radiant tube, a new type of radiant tube burner is proposed based on the flue gas recirculation technology,which can increase the flue gas circulation while ensuring continuous combustion. Specifically,the traditional combustion is first carried out in the radiant tube. After the temperature is higher than the auto-ignition point of the fuel,a large amount of flue gas is introduced,so that the U-shaped radiant tube reaches a flameless combustion state. At this time,the surface temperature is more uniform and the NO_x emission is lower. Through the establishment of a mathematical model of the U-shaped radiant tube with the burner,supplemented by experimental verification,the flameless combustion characteristics in the U-shaped radiant tube were explored,including the combustion state in the radiant tube,the uniformity of surface temperature and the NO_x emission,and the existing U-shaped radiant tube was compared and analyzed,and the influence of different smoke volume on the flameless combustion characteristics in the radiant tube was discussed. The research results show that the flameless combustion state is completely different from traditional combustion,under traditional combustion,there is an obvious local high temperature zone in the front of the radiant tube;with the introduction and further increase of the volume of cigarette smoking,the peak temperature continues to drop,and the high temperature zone. There is a phenomenon of transfer to the rear of the radiant tube. When the flameless combustion state is reached,the local high temperature area disappears;the flameless combustion greatly improves the surface temperature uniformity of the radiant tube,the extreme value of the temperature difference between the radiant tube wall is reduced from 110 K to 35 K,and the temperature uniformity coefficient is reduced from 9% to 2.9%,which is conducive to improving the actual temperature of the radiant tube. Service life;the emission of pollutant NO_x is reduced,from the initial 0.022%to less than 0.000 1%.

Key words： continuous annealing furnace radiant tube recirculation flue gas flameless combustion NO_x

Received: 20 July 2021

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	XU Jia-qiang
	SONG Zhong-hua
	PAN Ni
	TAN Fang-guan
	XU Xue-cheng
	HE Zhu

Cite this article:

XU Jia-qiang,SONG Zhong-hua,PAN Ni等. Numerical simulation on flameless combustion in U-shaped radiant tube for continuous annealing furnace[J]. Iron and Steel, 2022, 57(1): 143-150.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20210409 OR http://www.chinamet.cn/Jweb_gt/EN/Y2022/V57/I1/143

[1] 天津市冷轧带钢厂试验小组. 放热型保护气体及辐射管加热元件的初步试验[J]. 钢铁,1975,10(1):38. (Tianjin Cold Rolling Strip Steel Plant Test Team. Preliminary test of exothermic protective gas and radiant tube heating element[J]. Iron and Steel,1975,10(1):38.)
[2] 徐钱,冯俊小,周闻华. 分级气体成分对燃气辐射管热过程影响的数值模拟及研究[J]. 工程科学学报,2017,39(1):96. (XU Qian,FENG Jun-xiao,ZHOU Wen-hua. Numerical simulation and research on the effect of graded gas composition on the thermal process of gas radiant tube[J]. Chinese Journal of Engineering Science,2017,39(1):96.)
[3] 涂卫国,刘赟赟,冯俊小,等. 辐射管加热技术综述 [J]. 工业炉,2007,29(3):15. (TU Wei-guo,LIU Yun-yun,FENG Jun-xiao,et al. Overview of radiant tube heating technology[J]. Industrial Furnace,2007,29(3):15.)
[4] 朱伟素. 辐射管辊底式热处理炉数学模型的研究与应用[J]. 中国冶金,2017,27(2):37. (ZHU Wei-su. Research and application of mathematical model of radiant tube roller hearth heat treatment furnace[J]. China Metallurgy,2017,27(2):37.)
[5] 陈晓海,吕成,汪磊川,等. 冷轧连续退火炉燃烧控制原理[J]. 钢铁研究学报,2012,24(s1):162. (CHEN Xiao-hai,LÜ Cheng,WANG Lei-chuan,et al. Principle of combustion control in continuous annealing furnace for cold rolling[J]. Journal of Iron and Steel Research,2012,24(s1):162.)
[6] 高仲龙,蒋大强. 带钢加热用辐射管[J]. 工业加热,1998(5):9. (GAO Zhong-long,JIANG Da-qiang. Radiant tube for strip heating[J]. Industrial Heating,1998(5):9.)
[7] 郭坛. 浅谈冷轧硅钢连续退火炉的设计及应用[J]. 工业炉,2017,39(5):5. (GUO Tan. Discussion on the design and application of continuous annealing furnace for cold-rolled silicon steel[J]. Industrial Furnace,2017,39(5):53.)
[8] 朱海贵. 连续镀锌线退火炉温度控制 [J]. 工业技术创新,2017,4(3):207. (ZHU Hai-gui. Annealing furnace temperature control of continuous galvanizing line[J]. Industrial Technology Innovation,2017,4(3):207.)
[9] 祝志超,程从前,王鲁,等. 退火炉辐射管破裂失效分析[J]. 金属热处理,2011,36(s1):334.(ZHU Zhi-chao,CHENG Cong-qian,WANG Lu,et al. Failure analysis of radiant tube rupture in annealing furnace[J]. Heat Treatment of Metals,2011,36(s1):334.)
[10] 刘顺明,李洋龙,侯大伟,等. 连续退火炉W型辐射管破损调研及优化措施[J]. 钢铁,2018,53(6):103. (LIU Shun-ming,LI Yang-long,HOU Da-wei,et al. Investigation on the damage of W-shaped radiant tube in continuous annealing furnace and optimization measures[J]. Iron and Steel,2018,53(6):103.)
[11] 白世宏,高恩运,柳庆坡,等. 连退炉辐射管长寿技术的研究[J]. 钢铁研究学报,2012,24(s1):174. (BAI Shi-hong,GAO En-yun,LIU Qing-po,et al. Study on longevity technology of radiant tubes in continuous furnace[J]. Journal of Iron and Steel Research,2012,24(s1):174.)
[12] 兰健,吕田,金永星. 烟气再循环技术研究现状及发展趋势[J]. 节能,2015(10):4. (LAN Jian,LÜ Tian,JIN Yong-xing. Research status and development trend of flue gas recycling technology[J]. Energy Conservation,2015(10):4.)
[13] 徐钱,冯俊小,周闻华,等. 分区分级双P型辐射管喷口结构位置特性[J]. 工程科学学报,2017,39(5):756. (XU Qian,FENG Jun-xiao,ZHOU Wen-hua,et al. The location characteristics of the zonal and hierarchical dual P-type radiant tube nozzle structure[J]. Chinese Journal of Engineering Science,2017,39(5):756.)
[14] 冯俊小,姜敏,周闻华,等. 带烟气循环的W型辐射管流动传热及NO_x排放特性[J]. 北京科技大学学报,2014,36(11):1552. (FENG Jun-xiao,JIANG Min,ZHOU Wen-hua,et al. Flow heat transfer and NO_x emission characteristics of W-shaped radiant tube with flue gas circulation[J]. Journal of University of Science and Technology Beijing,2014,36(11):1552.)
[15] 冯俊小,姜敏,曹亚平,等. W型辐射管低NO_x排放的数值研究[J]. 北京科技大学学报,2014,36(8):1094. (FENG Jun-xiao,JIANG Min,CAO Ya-ping,et al. Numerical study of low NO_x emissions from W-shaped radiant tubes[J]. Journal of University of Science and Technology Beijing,2014,36(8):1094.)
[16] 刘长春,徐邵亮,杨元博. 单端辐射管研究进展及发展方向[J]. 工业炉,2017,39(3):22. (LIU Chang-chun,XU Shao-liang,YANG Yuan-bo. Research progress and development direction of single-ended radiant tubes[J]. Industrial Furnace,2017,39(3):22.)
[17] 王志宁. 基于烟气再循环某85 t/h燃气锅炉低氮燃烧特性的研究[D]. 太原:太原理工大学,2019. (WANG Zhi-ning. Research on Low-Nitrogen Combustion Characteristics of an 85 t/h Gas Boiler Based on Flue Gas Recirculation[D]. Taiyuan:Taiyuan University of Technology,2019.)
[18] Wunning J A,Wunning J G. Flameless oxidation to reduce thermal no-formation[J]. Progress in Energy and Combustion Science,1997,23(2):81.
[19] MI J C,LI P F,ZHENG C G. Numerical simulation of flameless premixed combustion with an annular nozzle in a recuperative furnace[J]. Chinese Journal of Chemical Engineering,2010,18(1):10.
[20] MI J C,LI P F,DALLY B B,et al. Importance of initial momentum rate and air-fuel premixing on moderate or intense low oxygen dilution (MILD) combustion in a recuperative furnace[J]. Energy Fuels,2009,23(11):5349.
[21] 李鹏飞. 气体燃料MILD燃烧的实验和模拟研究[D]. 北京:北京大学,2013. (LI Peng-fei. Experimental and Simulation Study on the Combustion of Gas Fuel MILD[D]. Beijing:Peking University,2013.)
[22] 李鹏飞,米建春,B D B,等. MILD燃烧的最新进展和发展趋势[J]. 中国科学(技术科学),2011,41(2):135. (LI Peng-fei,MI Jian-chun,B D B,et al. The latest progress and development trend of MILD combustion[J]. Science in China(Technological Sciences),2011,41(2):135.)
[23] TIAN Y,LIN S H,LIU X L,et al. Comparative performance assessment of a u-shaped recuperative radiant tube under conventional and MILD combustion modes[J]. Journal of Energy Engineering,2018,144(3):10.
[24] TIAN Y,ZHOU X,JI X Y,et al. Applying moderate or intense low-oxygen dilution combustion to a co-axial-jet I-shaped recuperative radiant tube for further performance enhancement[J]. Energy,2019,171:149.
[25] 徐家强,董亮,郑晓龙,等. 辐射管燃烧器实现MILD燃烧的结构优化研究[J]. 冶金能源,2021,40(4):50. (XU Jia-qiang,DONG Liang,ZHENG Xiao-long,et al. Study on structure optimization of radiant tube burner for MILD combustion[J]. Energy for Metallurgical Industry,2021,40(4):50.)