1. School of Control Engineering, Northeastern University at Qinhuangdao, Qinhuangdao 066004, Hebei, China 2. College of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, Hebei, China 3. Research Institute of Science and Technology, Northeastern University, Shenyang 110819, Liaoning, China
Transverse Bending Characteristics in U-channel Forming of Tailor Rolled Blank
1. School of Control Engineering, Northeastern University at Qinhuangdao, Qinhuangdao 066004, Hebei, China 2. College of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, Hebei, China 3. Research Institute of Science and Technology, Northeastern University, Shenyang 110819, Liaoning, China
ժҪ Research on the formability of tailor rolled blank (TRB) is of good practical significance and application value because of the enormous potential of TRB in the aspect of automobile lightweight. However, the forming of TRB is problematic because of the varying properties; especially, springback is a main challenge. The transverse bending (bending axis is perpendicular to the rolling direction) of TRB U-channel was studied through simulation and experiment. The forming characteristics of TRB U-channel during transverse bending were analyzed. The mechanisms of forming defects, including bending springback and thickness transition zone (TTZ) movement, were revealed. On this basis, effects of blank geometric parameters on springback and TTZ movement were discussed. The results indicate that springback and TTZ movement happen during transverse bending of TRB U-channel. Nonuniform stress distribution is the most fundamental reason for the occurrence of springback of TRB during transverse bending. Annealing can eliminate nonuniform stress distribution, and thus diminish springback of TRB, especially springback on the thinner side. Therefore, springback of the whole TRB becomes more uniform. However, annealing can increase the TTZ movement. Blank thickness and TTZ position are the main factors affecting the formability of TRB U-channel during transverse bending.
Abstract��Research on the formability of tailor rolled blank (TRB) is of good practical significance and application value because of the enormous potential of TRB in the aspect of automobile lightweight. However, the forming of TRB is problematic because of the varying properties; especially, springback is a main challenge. The transverse bending (bending axis is perpendicular to the rolling direction) of TRB U-channel was studied through simulation and experiment. The forming characteristics of TRB U-channel during transverse bending were analyzed. The mechanisms of forming defects, including bending springback and thickness transition zone (TTZ) movement, were revealed. On this basis, effects of blank geometric parameters on springback and TTZ movement were discussed. The results indicate that springback and TTZ movement happen during transverse bending of TRB U-channel. Nonuniform stress distribution is the most fundamental reason for the occurrence of springback of TRB during transverse bending. Annealing can eliminate nonuniform stress distribution, and thus diminish springback of TRB, especially springback on the thinner side. Therefore, springback of the whole TRB becomes more uniform. However, annealing can increase the TTZ movement. Blank thickness and TTZ position are the main factors affecting the formability of TRB U-channel during transverse bending.
��������:National Natural Science Foundation of China;Natural Science Foundation of Hebei Province;Natural Science Foundation of Hebei Province;China Postdoctoral Science Foundation
ͨѶ����:
��Ӣƽ
E-mail: gyp@ysu.edu.cn
����:
Hua-wei ZHANG,,Ying-ping GUAN,Jia-lu WU,Xiang-hua LIU. Transverse Bending Characteristics in U-channel Forming of Tailor Rolled Blank[J]. �й������ڿ���, 2016, 23(12): 1249-1254.
Hua-wei ZHANG,,Ying-ping GUAN,Jia-lu WU,Xiang-hua LIU. Transverse Bending Characteristics in U-channel Forming of Tailor Rolled Blank. Chinese Journal of Iron and Steel, 2016, 23(12): 1249-1254.
2016, Vol. 23 
