|
|
|
| Effect of pH and applied stress on hydrogen sulfide stress corrosion behavior of HSLA steel based on electrochemical noise analysis |
| Xiao-hua Li1,2, Chen-xi Liu2, Teng Zhang3, Chuan-tao Lv4, Jiang-cheng Liu4, Ran Ding2, Zhi-ming Gao2, Rui Wang1, Yong-chang Liu2 |
| 1 School of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China 2 State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300350, China 3 Southwestern Institute of Physics, Chengdu 610041, Sichuan, China 4 Tianjin Pipe Corporation, Tianjin 300301, China |
|
|
|
|
Abstract The influence mechanism of pH and the externally applied stress on sulfide stress corrosion cracking behavior based on the joint analysis of the in situ electrochemical noise and microstructure was studied. The results showed that Ht in solution changes the composition and structure of corrosion product film by affecting the concentration of S2 and Fe2t near the anode surface. When the pH increased from 2.6 to 3.6 and 4.6, the corrosion product film changed from porous Mackinawite to dense and stable FeS. The change in corrosion product type delayed the crack initiation time by 10.5 and 45.5 h, while the uniform corrosion time was prolonged by 6.1 and 46 h, respectively, delaying SSC behavior. After increasing the applied stress, the local plastic deformation on the material surface increases the porosity and crack rate of the corrosion product film and becomes a fast propagation channel for SSC cracks. When the applied stress is 110% of the actual yield strength of the material, the initiation time of stress corrosion cracking is 6 and 18.1 h earlier than that of 90% and 100%, respectively. The local corrosion time was extended by 23.5 and 8.2 h, respectively, accelerating SSC behavior.
|
|
|
|
|
|
| Cite this article: |
|
Xiao-hua Li,Chen-xi Liu,Teng Zhang, et al. Effect of pH and applied stress on hydrogen sulfide stress corrosion behavior of HSLA steel based on electrochemical noise analysis[J]. Journal of Iron and Steel Research International, 2023, 30(12): 2531-2540.
|
|
|
|
| [1] |
Xue-cheng Peng, Han-jie Guo, Xin-fang Zhang, Yi-wa Luo, Ye Sun, Jing Guo, Rong-guang Yang, Xiao-dan Zheng. Strengthening and control of second-phase particle precipitation in ferritic/austenitic/martensitic heat-resistant alloys: a review[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(1): 3-23. |
| [2] |
Jing Guo, Hai-jing Wang, Shuang-juan Liu, Peng Zhang, Jing-yu Tang, Wei-yang Zhang, Han-jie Guo, Peng-cheng Wang, Cai Meng. Interface optimization of graphene paper–Cu composite prepared by electrodeposition[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(1): 64-73. |
| [3] |
Neng-yong Ye, Guang-liang Zhang, Tian-yue Huang, Ming Cheng, Shi-hong Zhang, Lei Wang. Orientational growth behavior and mechanism of delta (δ) phase precipitation in cold-rolled Inconel 718 alloy during heat treatment[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(1): 264-274. |
| [4] |
Hai-liang Zhang, Ling-xu Yang, Qian Wang, Jiang-tao Wu, Suo-de Zhang, Chao-liu Zeng. Hot corrosion behaviors of 921A alloy and HVAF-sprayed Fe-based amorphous coating covered with KCl–ZnCl2 salts[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(8): 1537-1549. |
| [5] |
Yu-fan Shi, Cheng-jun Guo, Ming-quan Yuan, Zhen-bin Jia, Gui-huan An, Xiang-peng Xiao, Bin Yang. Effect of solidification rate on dendrite segregation and mechanical properties of Cu–15Ni–8Sn alloy prepared by directional solidification[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(8): 1586-1597. |
| [6] |
Da-lei Zhang1, Ran Liu, Ying-shuang Liu, Shao-hua Xing, Zong-hao He, Yao Qian, Jin-zeng Liu, Xiao-hui Dou, Xin-wei Zhang. Combined experimental and simulation study on corrosion behavior of B10 copper–nickel alloy welded joint under local turbulence[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(8): 1598-1612. |
|
|
|
|
2023, Vol. 30 
