金属板材应变硬化指数<i>n</i>与其屈强比的关系

doi:10.13228/j.boyuan.issn1001-0777.20220005

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (1194 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Based on the Hollomon relation, the corresponding relationship between the n value and the yield ratio was deduced. According to this formula, the value of n of one material with certain thickness was firstly measured, which was then substituted to obtain the value of material constant C. For the materials of this type of steel with other thicknesses, the measurement of yield strength R_p0.2 and tensile strength R_m was only required to calculate the value of n according to the formula. The calculation values and measurement values of n of typical material were compared. The results showed that the proposed method for the calculation of n was accurate and simple to use, which greatly simplified the work of determining the n value of the same steel type. This method was especially applicable for the estimation of n value of ultra-thin materials or ultra-thick materials, which was difficulty measured in the laboratory.

Key words： hardening index n value yield ratio corresponding relationship

Received: 07 February 2022

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	WANG Feilong
	QIN Rongguang
	ZHOU Sanbao
	YIN Jingjing
	JIN Yang

Cite this article:

WANG Feilong,QIN Rongguang,ZHOU Sanbao等. Relationship between strain hardening index (n) of metal sheet and its yield ratio[J]. PHYSICS EXAMINATION AND TESTING, 2023, 41(1): 16-20.

URL:

http://www.chinamet.cn/Jweb_wlcs/EN/10.13228/j.boyuan.issn1001-0777.20220005 OR http://www.chinamet.cn/Jweb_wlcs/EN/Y2023/V41/I1/16

[1]	中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会. GB/T 5028—2008金属材料薄板和薄带拉伸应变硬化指数(n值)的测定[S]. 北京:中国标准出版社,2008.
[2]	李立军,祝洪川. 汽车冲压零件分类的一种新方法[J]. 钢铁研究,2001(4):33.
[3]	Kumar D R. Formability analysis of extra-deep drawing steel[J]. Journal of Materials Processing Technology, 2002,130:31.
[4]	李春光,蒋光锐,章军. 深冲IF钢应变硬化指数n值研究[C]// 2014年全国轧钢生产技术会议文集(上). 无锡:中国金属学会,2014:544.
[5]	翁文达,陈志国,钟文达. 应变硬化指数n值的确定方法[J]. 物理测试,1991,8(2):35.
[6]	杨尚林. 关于应变硬化指数影响因素的探讨[J]. 物理测试,1996,13(1):21.
[7]	王印培. 应变硬化指数的一种简易求法[J]. 物理测试,1986,3(3):48.
[8]	李英发. 估计应变硬化指数的一种简易方法[J]. Metal Progress,1985(8):59.
[9]	张家义.一种测定应变硬化指数的简易方法[J]. 钢铁研究,1990,55(2):117.
[10]	刘瑞堂,刘长禄,赵景瑞,等.钢材应变强化指数与屈强比的关系[J].理化检验(物理分册),1983,19(5):24.
[11]	孙东继,林建平,胡巧声,等.金属板料幂指型硬化模型应变强化系数K值研究[J]. 塑性工程学报,2009,16(1):149.
[12]	顾为群,黄明志,骆竞晞. 幂乘硬化方程相互关系和强化系数k值的研究[J]. 西安交通大学学报,1987,21(6):19.
[13]	宋玉泉,程永春,刘颖. 拉伸变形应变硬化指数的力学涵义及其规范测量[J].中国科学(E辑),2000,30(3):200.
[14]	方健,魏毅静,王承忠.拉伸应变硬化指数的解析测定及力学分析[J]. 塑性工程学报,2003,10(3):12.