固溶处理对00Cr27Ni7Mo5N不锈钢的组织及力学性能的影响

黄盛,,宋志刚,郑文杰,尹建成

钢铁 ›› 2011, Vol. 46 ›› Issue (12) : 71-75.

欢迎访问《钢铁》官方网站!今天是 2025年8月4日 星期一
钢铁 ›› 2011, Vol. 46 ›› Issue (12) : 71-75.
钢铁材料

固溶处理对00Cr27Ni7Mo5N不锈钢的组织及力学性能的影响

  • 黄盛1,2,宋志刚2,郑文杰2,尹建成1
作者信息 +

Influence of Solution Temperature on Microstructure and Mechanical Properties of 00Cr27Ni7Mo5N

  • 黄盛1,2,宋志刚2,郑文杰2,尹建成1
Author information +
文章历史 +

摘要

研究了不同固溶处理温度对特超级双相不锈钢00Cr27Ni7Mo5N组织及力学性能的影响。采用光镜、扫描电镜、能谱仪、显微硬度、冲击和拉伸测试等手段研究σ相的析出规律及其对力学性能的影响。运用Thermo-Calc热力学软件计算00Cr27Ni7Mo5N相含量随温度的变化,并与测试结果进行对比分析。研究结果表明,当固溶温度在800~1050℃之间,00Cr27Ni7Mo5N有大量金属间化合物σ相析出,导致钢的强度和硬度增加,塑韧性显著下降。当固溶温度在1070~1200℃时,钢中σ相溶解,钢的塑韧性提高,硬度下降。1100℃固溶处理时,00Cr27Ni7Mo5N具有最佳的综合力学性能。

Abstract

The effect of solution temperature on the microstructure and properties of hyper duplex stainless steel 00Cr27Ni7Mo5N was investigated. σ phase precipitation and its effect on microstructure and mechanical properties were analyzed by OM, SEM, EDS, microhardness measurements, impact and tensile tests. The phase diagram was calculated with the Thermo-Calc thermodynamic software and compared with the experiment results. It can be conclude, the intermetallic compound σ phase precipitatesed in the range of 800-1050℃, leads to an obvious increase in the hardness and strength, a sharp decrease in the ductility and toughness;contrary results are obtained with increasing the solution temperature from 1070 to 1200℃, the optimum solution temperature of the steel is about 1100℃.

关键词

特超级双相不锈钢 / σ相 / 微观组织

Key words

hyper duplex stainless steel / σ phase / microstructure

图表

引用本文

导出引用
黄盛, 宋志刚, 郑文杰, . 固溶处理对00Cr27Ni7Mo5N不锈钢的组织及力学性能的影响[J]. 钢铁, 2011, 46(12): 71-75
HUANG Sheng, SONG Zhi-Gang, ZHENG Wen-Jie, et al. Influence of Solution Temperature on Microstructure and Mechanical Properties of 00Cr27Ni7Mo5N[J]. Iron and Steel, 2011, 46(12): 71-75

5

Accesses

0

Citation

Detail

段落导航
相关文章

/