特厚板连铸保护渣系列规划

doi:10.13228/j.boyuan.issn0449-749x.20150296

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (0 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要针对特厚板连铸工艺的特点，分析了传统的中厚板连铸保护渣与特厚板连铸保护渣的作用特征差异。根据不同钢种在结晶器内的凝固特性，对新钢特厚板连铸保护渣进行了系列规划，分为高碳钢连铸保护渣、包晶钢连铸保护渣、中碳低合金钢连铸保护渣3大类。在此基础上，提出了保护渣熔化温度、黏度、转折温度、结晶比例的控制范围。生产实践表明，设计的保护渣浇铸过程结晶器内状况良好，渣面无结团、结块现象，液渣层厚度合适，保护渣消耗量正常，铸坯表面质量优良，连铸生产工艺顺行。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	朱礼龙
	何生平
	毛敬华
	赵和明
	韩志伟
	王谦

关键词 ：特厚板, 连铸保护渣, 系列规划, 表面质量

Abstract：The characteristic differences between traditional mold fluxes for medium or thick slabs continuous casting and ultra-thick slabs continuous casting were analyzed based on the technological characteristics of ultra-thick slabs casting. Then，the systematization of mold fluxes was conducted after the discussion of solidification features of for different grades，and three mold flux groups were proposed：high carbon steels，peritectic steels and micro alloying steels with medium carbon content. Based on the classification，the control ranges of melting temperature、viscosity、break temperature and crystallization ratio of mold fluxes were put forward. Commercial production data reveals that with proposed mold fluxes，smooth and stable casting can be obtained and no sintering is observed. The thickness of liquid slag layer and consumption are suitable. The surface quality of slabs is perfect and the continuous casting process is smooth.

收稿日期: 2015-06-25 出版日期: 2016-03-18

引用本文:

朱礼龙，何生平，毛敬华，赵和明，韩志伟，王谦. 特厚板连铸保护渣系列规划[J]. 钢铁, 2016, 51(3): 44-48. ZHU Li-long，HE Sheng-ping，，MAO Jing-hua，ZHAO He-ming，HAN Zhi-wei，WANG Qian. Systematization of mold fluxes for ultra-thick slab continuous casting. Iron and Steel, 2016, 51(3): 44-48.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20150296 或 http://www.chinamet.cn/Jweb_gt/CN/Y2016/V51/I3/44

[1]	毛敬华, 王水根, 占贤辉.机型与防止特厚板坯表面裂纹的关系[J].连铸, 2014, (2):39-41
[1]	毛敬华, 王水根, 占贤辉.机型与防止特厚板坯表面裂纹的关系[J].连铸, 2014, (2):39-41
[2]	迟景灏, 甘永年等.连铸保护渣[M]. 沈阳:东北大学出版社, 1992.
[2]	迟景灏, 甘永年等.连铸保护渣[M]. 沈阳:东北大学出版社, 1992.
[3]	王水根, 冯科, 毛敬华, 韩志伟.特厚板坯连铸凝固传热研究[J].钢铁技术, 2011, (6):19-22
[3]	王水根, 冯科, 毛敬华, 韩志伟.特厚板坯连铸凝固传热研究[J].钢铁技术, 2011, (6):19-22
[4]	王谦, 何生平, 李玉刚, 朱礼龙, 吴婷, 陈卓.中国连铸保护渣技术现状及发展需求[J].连铸, 2014, (05):1-8
[4]	王谦, 何生平, 李玉刚, 朱礼龙, 吴婷, 陈卓.中国连铸保护渣技术现状及发展需求[J].连铸, 2014, (05):1-8
[5]	Mills K.C, Fox A.B., Li Z. & Thackray R.P. .Performance and properties of mold fluxes[J].Ironmaking & Steelmaking, 2005, 32(1):26-34
[5]	Mills K.C, Fox A.B., Li Z. & Thackray R.P. .Performance and properties of mold fluxes[J].Ironmaking & Steelmaking, 2005, 32(1):26-34
[6]	K.Nakajima..Heat transfer and lubrication behavior in mold at high-speed continuous casting of steel slabs[J].CAMP-ISIJ, 1992, 5:1221-1224
[6]	K.Nakajima..Heat transfer and lubrication behavior in mold at high-speed continuous casting of steel slabs[J].CAMP-ISIJ, 1992, 5:1221-1224
[7]	Grieveson P, et al.Physical properties of casting powders: Part 2 Mineralogical constitution of slags formed by powders[J].Ironmaking and Steelmaking, 1988, 15(4):181-186
[7]	Grieveson P, et al.Physical properties of casting powders: Part 2 Mineralogical constitution of slags formed by powders[J].Ironmaking and Steelmaking, 1988, 15(4):181-186