EAF＋AOD＋LF流程冶炼310S耐热钢夹杂物控制

doi:10.13228/j.boyuan.issn0449-749x.20160313

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (0 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要为了进一步提高310S钢种的洁净度，满足其耐蚀性能。利用化学分析、金相及小样电解、扫描电镜等手段研究了以EAF＋AOD＋LF流程生产310S耐热钢原精炼工艺下的钢水洁净度，并在此基础上提出了优化方案。结果表明，通过适当提高AOD还原炉渣碱度、LF进站采用铝粉进行深脱氧和延长大流量底吹氩气搅拌时间等手段提高了310S钢水洁净度，其中连铸坯[w(T[O])]由0.003 4%下降到0.002 5%，消除了直径大于30 μm的大颗粒夹杂物，直径超过15 μm的夹杂物数量减少了5.8%，1～7 μm的弥散夹杂物数量增加了15.5%。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	翟俊
	刘浏

关键词 ： 310S, 夹杂物, AOD, LF

Abstract：For achieving preferable corrosion resistance，the cleanliness of 310S stainless steel needs to be improved further. The cleanliness of 310S heat resistant steel produced by EAF＋AOD＋LF process were studied by means of chemical analysis，metallographic observation as well as scanning electron microscope. Based on the results，the optimizing solutions were put forward. The results indicated that increasing AOD slag basicity to 2.0，adding Al in LF process to deep deoxidizing and prolonging the Ar blowing time to remove inclusions with large size were very effective. After optimizing，[w(T[O])] in steel slab decresed from 0.003 4%to 0.002 5%，and the amount of inclusions with the size of 1-7 μm increased by 15.5%，the amount of inclusions larger than 15 μm decreased by 5.8%，and large inclusions over 30 μm were approximately eliminated.

收稿日期: 2016-07-14 出版日期: 2017-05-04

引用本文:

翟俊，，刘浏. EAF＋AOD＋LF流程冶炼310S耐热钢夹杂物控制[J]. 钢铁, 2017, 52(5): 31-35. ZHAI Jun，，LIU Liu. Investigations on inclusion control of heat resistant steel 310S in EAF＋AOD＋LF process. Iron and Steel, 2017, 52(5): 31-35.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20160313 或 http://www.chinamet.cn/Jweb_gt/CN/Y2017/V52/I5/31

[1]	高津刚，张虎平。关于0Cr25Ni20钢轧制开裂问题的研究[J].天津冶金。2000:21-22.
[1]	高津刚，张虎平。关于0Cr25Ni20钢轧制开裂问题的研究[J].天津冶金。2000:21-22.
[2]	Parda J M, Carvalho S S. Failure analysis of AISI 310S plate in an inert gas generator used in off-shore oil platform[J]. Engineering Failure Analysis,2011(18):1435-1444.
[2]	Parda J M, Carvalho S S. Failure analysis of AISI 310S plate in an inert gas generator used in off-shore oil platform[J]. Engineering Failure Analysis,2011(18):1435-1444.
[3]	李正邦.超洁净钢和零非金属夹杂钢[J].2004,25(4):24-25.
[3]	李正邦.超洁净钢和零非金属夹杂钢[J].2004,25(4):24-25.
[4]	Mizuno K，Todoroki H，Noda M，et a1．Effects ofA1 and Ca in Ferrosilicon Alloys for Deoxidation on Inclusion Composition in Type 304 Stainless Steel[J]．Iron and Steelmaker,2001(8)：93-101.
[4]	Mizuno K，Todoroki H，Noda M，et a1．Effects ofA1 and Ca in Ferrosilicon Alloys for Deoxidation on Inclusion Composition in Type 304 Stainless Steel[J]．Iron and Steelmaker,2001(8)：93-101.
[5]	陈家祥.炼钢常用图标数据手册[M].冶金工业出版社 768-781.
[5]	陈家祥.炼钢常用图标数据手册[M].冶金工业出版社 768-781.
[6]	张荣品. 150t椭圆型钢包吹氩精炼优化研究[J]. 梅山科技,2003,04:31-34.
[6]	张荣品. 150t椭圆型钢包吹氩精炼优化研究[J]. 梅山科技,2003,04:31-34.
[7]	李道明.不锈钢中非金属夹杂物的危害及去除[J].山西冶金，2008,31（4）：24-26.
[7]	李道明.不锈钢中非金属夹杂物的危害及去除[J].山西冶金，2008,31（4）：24-26.