Abstract:Online flatness measurement and closed-loop control is necessary requirement to produce high-end and fine cold rolled strip steel. The independent innovation of the flatness measurement and control technology is the important demand to upgrade steel industry and build steel powerhouse in China. The strategic conception to promote the technology innovation is explained systematically,on the basis of the brief introduction of the basic situations,the development directions and the existing problems of the flatness measurement and control technology of cold steel strip rolling. The main research contents include the principle and model of the channel coupling and the signal decoupling of the flatness measurement,the dynamic simulating and decoupling models of the flatness regulation and control,the deep smarts modeling of the flatness regulation and control,and the computing simulation and the digital twin,the laboratory experiment and the industry experiment of the flatness measurement and control system. The key scientific and technical problems to have to be solved include the channel coupling mechanics and the signal decoupling method of the flatness meter,the dynamic modeling and decoupling methods of the flatness regulation and control,and the deep smarts modeling method of the flatness regulation and control,and the digital twin method of the flatness measurement and control. The innovative goals are to establish the methods and models of the flatness signal decoupling and dynamic intelligence control,develop the high precision Cyber-Physical Systems (CPS) of the flatness measurement and control with international advanced level,and upgrade the theoretical and technical level of the flatness measurement and control. The research approaches are constructed. Taking the flatness measurement and control system of 6-high mills for example,firstly the flatness measurement decoupling,the whole roll adjustment and the local roll adjustment are researched,and then the three subsystems are integrated into an integrated system,by means of the theoretical analysis,the modeling and simulation,the experiment study,and the machine learning. The integrated system is improved and advanced by the methods of the computing simulation and the digital twin,the laboratory study and the industrial experiment. The above innovation strategy aims to promote the deep research of the flatness measurement and control technology,and improve the intelligence level of steel industry.
刘宏民, 于华鑫, 王东城, 宋明明, 张帅, 张桐源. 冷轧带钢板形测控前沿技术的创新方略[J]. 钢铁, 2023, 58(4): 77-86.
LIU Hong-min, YU Hua-xin, WANG Dong-cheng, SONG Ming-ming, ZHANG Shuai, ZHANG Tong-yuan. Innovative strategy on frontier flatness measurement and control technology of cold strip steel rolling[J]. Iron and Steel, 2023, 58(4): 77-86.
[1] 王国栋. 钢铁行业技术创新和发展方向[J]. 钢铁,2015,50(9):1.(WANG Guo-dong. Technology innovation and development direction of iron and steel industry[J]. Iron and Steel,2015,50(9):1.) [2] 中国金属学会,中国钢铁工业协会. 冷轧机板形控制核心技术自主研发与工业应用[J]. 中国冶金,2013,23(4):61.(The Chinese Society for Metals,China Iron and Steel Association. Independent research and development and industrial application of core technology of flatness control for cold rolling mill[J]. China Metallurgy,2013,23(4):61.) [3] Bemporad A,Bernardini D,Cuzzola F A,et al. Optimization-based automatic flatness control in cold tandem rolling[J]. Journal of Process Control,2010,20(4):396. [4] 刘宏民,刘军,于丙强,等. 带钢冷轧机整辊无线式板形仪和智能板形控制系统[J]. 机械工程学报,2017,53(12):87.(LIU Hong-min,LIU Jun,YU Bing-qiang,et al. Entire roller wireless shape meter and intelligent shape control system for cold steel strip mills[J]. Journal of Mechanical Engineering,2017,53(12):87.) [5] WANG Dong-cheng,LIU Hong-min,LIU Jun. Research and development trend of shape control for cold rolling strip[J]. Chinese Journal of Mechanical Engineering,2017,30(5):1248. [6] 于华鑫,刘宏民,徐扬欢,等. 冷轧带材板形测控系统国家标准解读[J]. 钢铁,2019,54(10):52.(YU Hua-xin,LIU Hong-min,XU Yang-huan,et al. Interpretation of national standards for cold rolled strip shape detection and control system[J]. Iron and Steel,2019,54(10):52.) [7] 刘宏民,于华鑫,王东城,等. 冷轧带钢板形测控技术的发展状况和关键问题[J]. 钢铁,2022,57(11):22.(LIU Hong-min,YU Hua-xin,WANG Dong-cheng,et al. Development state and key problems on flatness measurement and control technology of cold strip steel rolling[J]. Iron and Steel,2022,57(11):22.) [8] 于华鑫,张桐源,张帅,等. 整辊式板形辊挠曲影响信号的快速识别和消除[J]. 仪器仪表学报,2021,42(3):192.(YU Hua-xin,ZHANG Tong-yuan,ZHANG Shuai,et al. Fast recognition and elimination of the interference signal caused by bending deformation of the whole roller seamless flatness meter[J]. Chinese Journal of Scientific Instrument,2021,42(3):192.) [9] YU Hua-xin,ZHANG Tong-yuan,ZNANG Shuai,et al. Quick recognition and elimination of an additional signal caused by deflection of an integral roller flatness meter[J]. Iron and Steel Institute of Japan,International,2021,61(10):2571. [10] 王东城,徐扬欢,于华鑫,等. 整辊内嵌式板形仪挠度干扰信号的消除方法[J]. 钢铁,2020,55(10):56. (WANG Dong-cheng,XU Yang-huan,YU Hua-xin,et al. Method of eliminating deflection interference signal of whole roll embedded flatness meter[J]. Iron and Steel,2020,55(10):56.) [11] 于华鑫,王东城,刘宏民,等. 冷轧带材整辊式板形仪通道耦合与解耦[J]. 钢铁,2019,54(11):63.(YU Hua-xin,WANG Dong-cheng,LIU Hong-min,et al. Channel coupling and decoupling of seamless flatness meter for cold rolling strip[J]. Iron and Steel,2019,54(11):63.) [12] YU Hua-xin,WANG Dong-cheng,LIU Hong-min,et al. Modelling and application of signal decoupling of adjacent channels of a whole-roller seamless flatness meter[J]. Iron and Steel Institute of Japan,International,2020,60(5):939. [13] 王东城,张威,王志杰,等. 六辊冷轧机板形快速预报方法[J]. 钢铁,2016,51(9):51.(WANG Dong-cheng,ZHANG Wei,WANG Zhi-jie,et al. Fast shape prediction method for six-high cold rolling mill[J]. Iron and Steel,2016,51(9):51.) [14] WANG Dong-cheng,LIU Hong-min. A model coupling method for shape prediction[J]. Journal of Iron and Steel Research,International,2012,19(2):22. [15] LIU Hong-min,ZHANG Xiu-ling,WANG Ying-rui. Transfer matrix method of flatness control for strip mills[J]. Journal of Materials Processing Technology,2005,166:237. [16] LIU Hong-min,HE Hai-tao,SHAN Xiu-ying,et al. Flatness control based on dynamic effective matrix for cold strip mills[J]. Chinese Journal of Mechanical Engineering,2009,22(2):41. [17] LIU Hong-min,SHAN Xiu-ying,JIA Chun-yu. Theory-intelligent dynamic matrix model of flatness control for cold rolled strips[J]. Journal of Iron and Steel Research International,2013,20(8):1. [18] SONG Ming-ming,LIU Hong-min,WANG Dong-cheng,et al. Decoupling strategy and dynamic decoupling model of flatness control in cold rolling strip[J]. Iron and Steel Institute of Japan,International,2020,60(2):286. [19] SONG Ming-ming,LIU Hong-min,XU Yang-huan,et al. Decoupling strategy and mechanism-intelligent model of non-square flatness control system[J]. Iron and Steel Institute of Japan,International,2021,61(10):2552. [20] 张秀玲,刘宏民. 板形模式识别的GA-BP模型和改进的最小二乘法[J]. 钢铁,2003,38(10):29.(ZHANG Xiu-ling,LIU Hong-min. GA-BP model of flatness pattern recognition and improved least-squares method[J]. Iron and Steel,2003,38(10):29.) [21] 宋明明,王东城,张帅,等. 基于循环神经网络的板形模式识别模型[J]. 钢铁,2018,53(11):56.(SONG Ming-ming,WANG Dong-cheng,ZHANG Shuai,et al. Flatness pattern recognition model based on recurrent neural network[J]. Iron and Steel,2018,53(11):56.) [22] 刘宏民,丁开荣,李兴东,等. 板形标准曲线的理论计算方法[J]. 机械工程学报,2008,44(8):137.(LIU Hong-min,DING Kai-rong,LI Xing-dong,et al. Theoretical computational method of shape standard curve[J]. Chinese Journal of Mechanical Engineering,2008,44(8):137.)