GCr15轴承钢连铸过程MgO·Al<sub>2</sub>O<sub>3</sub>夹杂物形成机理

doi:10.13228/j.boyuan.issn0449-749x.20220703

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (3000 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为了研究GCr15轴承钢浇铸过程MgO·Al₂O₃夹杂物形成原因,以改善钢的可浇性,对LF结束、RH结束、中间包冲击区、中间包浇铸区进行夹杂物全流程分析。LF结束夹杂物主要为镁铝尖晶石,并含有少量钙铝酸盐夹杂物。RH真空处理后镁铝尖晶石夹杂物被高效化去除,钢液中仅剩少量低熔点和高熔点钙铝酸盐夹杂物,中间包浇铸时可以在钢液中检测到许多MgO·Al₂O₃夹杂物。采用不含氧化镁的中间包覆盖剂和铝质中间包内衬,在不改变连铸其他工艺参数条件下,中间包MgO·Al₂O₃夹杂物数量并没有得到显著降低,中间包钢液中仍然可以检测到许多MgO·Al₂O₃夹杂物,这说明中间包钢-渣-耐火材料间的反应并不是MgO·Al₂O₃夹杂物的生成原因。向铁质提桶取样器中加入成分以SiO₂、Cr₂O₃、Fe₂O₃为主的铬质引流砂,并利用该铁质提桶取样器对RH破空后钢水进行取样,尽管钢水总氧质量分数增加0.000 1%,但可以在所取的钢样中检测到许多MgO·Al₂O₃夹杂物,说明钢液的轻微氧化对MgO·Al₂O₃夹杂物形成具有重要的影响。通过分析中间包覆盖剂成分,发现浇铸过程覆盖剂碱度偏低,Cr₂O₃和FeO含量偏高,且同一炉钢水浇铸后期覆盖剂中Cr₂O₃、FeO含量较浇铸前期有所降低,说明浇铸过程覆盖剂会向钢水传氧,由此造成对钢液的氧化,因此,覆盖剂成分的稳定控制对于轴承钢MgO·Al₂O₃夹杂物的形成具有重要影响。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	张建斌
	徐建飞
	王昆鹏
	王郢
	杨谱
	陈廷军

关键词 ：轴承钢, 连铸, MgO·Al₂O₃, 氧化, 中间包, 覆盖剂

Abstract：The compositions of inclusions were analyzed in GCr15 steel in LF refining, RH degassing and continuous casting. The inclusions were composed of MgO·Al₂O₃ with a small amount of calcium aluminate after LF refining. Many MgO·Al₂O₃ inclusions were detected in the continuous casting although the inclusions were calcium aluminate after RH degassing. Using Al₂O₃-based tundish working lining and low content of MgO covering flux, and unchanging other parameters of continuous casting, MgO·Al₂O₃ inclusions were also be detected in large numbers in the tundish, indicating the reaction of steel-slag-refractory in the tundish was not the mainly reason for the formation of MgO·Al₂O₃ inclusions. However, many MgO·Al₂O₃ inclusions could be detected when the molten steel without MgO·Al₂O₃ inclusions reacted with the packing sand with high contents of SiO₂, Cr₂O₃ and Fe₂O₃, which means the slight oxidation of molten steel could lead to the formation of MgO·Al₂O₃ inclusions. High contents of FeO and Cr₂O₃were found in the tundish flux and decreased with the casting goes on, indicating the existence of the reactions between Al in the molten steel and FeO, Cr₂O₃in the tundish flux, which leads to the oxidation of molten steel. Therefore, the composition control of tundish flux was important to the formation of MgO·Al₂O₃ inclusions.

Key words： GCr15 continuous casting MgO·Al₂O₃ oxidation tundish covering flux

收稿日期: 2022-11-13

引用本文:

张建斌, 徐建飞, 王昆鹏, 王郢, 杨谱, 陈廷军. GCr15轴承钢连铸过程MgO·Al₂O₃夹杂物形成机理[J]. 钢铁, 2023, 58(5): 83-91. ZHANG Jian-bin, XU Jian-fei, WANG Kun-peng, WANG Ying, YANG Pu, CHEN Ting-jun. Formation mechanism of MgO·Al₂O₃ inclusions in GCr15 steel in continuous casting[J]. Iron and Steel, 2023, 58(5): 83-91.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20220703 或 http://www.chinamet.cn/Jweb_gt/CN/Y2023/V58/I5/83

[1] 李权辉, 陶镳, 徐志祥, 等. 连铸保护渣对GCr15轴承钢铸坯渣沟缺陷的影响[J]. 连铸, 2021(1): 55. (LI Quan-hui, TAO Biao, XU Zhi-xiang, et al. Effect of mold slag on slag-scratch on continuous casting billet of GCr15 bearing steel[J]. Continuous Casting, 2021(1): 55.)
[2] 史智越, 徐海峰, 许达, 等. 冶金工艺对GCr15高周旋转弯曲疲劳性能的影响[J]. 钢铁, 2018, 53(11): 85. (SHI Zhi-yue, XU Hai-feng, XU Da, et al. Effects of metallurgical craftwork on high bending fatigue performance of GCr15 steel during high cycle rotation[J]. Iron and Steel, 2018, 53(11): 85.)
[3] 车晓健, 杨卯生, 唐海燕, 等. 高性能GCr15轴承钢中夹杂物控制与疲劳性能[J]. 钢铁, 2018, 53(5): 76. (CHE Xiao-jian, YANG Mao-sheng, TANG Hai-yan, et al. Inclusion control and fatigue performance in high performance GCr15 bearing steel[J]. Iron and Steel, 2018, 53(5): 76.)
[4] 田超, 刘剑辉, 董瀚. 高洁净轴承钢夹杂物评价与滚动接触疲劳寿命[J]. 上海金属, 2018, 40(4): 1. (TIAN Chao, LIU Jian-hui, DONG Han. Inclusions evaluation and rolling contact fatigue life of high clean bearing steels[J]. Shanghai Metals, 2018, 40(4): 1.)
[5] 王坤, 胡锋, 周雯, 等. 轴承钢研究现状及发展趋势[J]. 中国冶金, 2020, 30(9): 119. (WANG Kun, HU Feng, ZHOU Wen, et al. Research status and development trend of bearing steel[J]. China Metallurgy, 2020, 30(9): 119.)
[6] 龙鹄, 成国光, 丘文生, 等. 轴承钢中大尺寸夹杂物的特征、来源及改进工艺[J]. 中国冶金, 2020, 30(9): 53. (LONG Hu, CHENG Guo-guang, QIU Wen-sheng, et al. Characteristics, sources analysis of large size inclusions and technical improvement during bearing steel production[J]. China Metallurgy, 2020, 30(9): 53.)
[7] 李永超, 卢彩玲, 左健成, 等. 轴承钢中间包首炉大型夹杂物分析及控制[J]. 连铸, 2021(3): 35. (LI Yong-chao, LU Cai-ling, ZUO Jian-cheng, et al. Analysis and control of macro-inclusions of bearing steel in tundish first heat[J]. Continuous Casting, 2021(3): 35.)
[8] 马帅, 李阳, 姜周华, 等. Ce对440C不锈轴承钢夹杂物演变的影响[J]. 中国冶金, 2022, 32(6): 71. (MA Shuai, LI Yang, JIANG Zhou-hua, et al. Effect of Ce on inclusion evolution for 440C stainless bearing steel[J]. China Metallurgy, 2022, 32(6): 71.)
[9] 朱雷敏, 李莉娟, 罗坤坤, 等. PMO对GCr15轴承钢连铸坯中MnS夹杂物的影响[J]. 中国冶金, 2021, 31(12): 32. (ZHU Lei-min, LI Li-juan, LUO Kun-kun, et al. Effect of PMO on MnS inclusions in continuous casting billet of GCr15 bearing steel[J]. China Metallurgy, 2021, 31(12): 32.)
[10] 王昆鹏, 王郢, 徐建飞, 等. 轴承钢二次精炼过程夹杂物演变规律[J]. 钢铁, 2022, 57(6): 42. (WANG Kun-peng, WANG Ying, XU Jian-fei, et al. Investigation on evolution of inclusions in bearing steel during secondary refining[J]. Iron and Steel, 2022, 57(6): 42.)
[11] 王康豪, 姜敏, 李凯伦, 等. GCr15轴承钢BOF-LF-RH-CC流程夹杂物的生成及演变[J]. 钢铁, 2022, 57(10): 64. (WANG Kang-hao, JIANG Min, LI Kai-lun, et al. Formation and evolution of inclusions in GCr15 bearing steel produced by process of BOF-LF-RH-CC[J]. Iron and Steel, 2022, 57(10): 64.)
[12] 蒋鲤平, 徐建飞, 王昆鹏, 等. 高碳铬GCr15轴承钢中镁铝夹杂物形成与控制工艺实践[J]. 特殊钢, 2022, 43(4): 41. (JIANG Li-ping, XU Jian-fei, WANG Kun-peng, et al. Formation of magnesium-aluminum inclusion in high carbon chromium GCr15 bearing steel and control process practice[J]. Special Steel, 2022, 43(4): 41.)
[13] 李林,江野,吴建永,等.GCr15钢浇注过程浸入式水口结瘤的原因及控制[J]. 上海金属, 2020, 42(6):35. (LI Lin, JIANG Ye, WU Jian-yong, et al. Formation and control of blockage at submerged nozzle of mold during GCr15 steel casting[J]. Shanghai Metals, 2020, 42(6):35.)
[14] 赵新凯, 田凤喜, 高文娟, 等. 轴承钢连铸过程中非金属夹杂物群迁移行为的分析[J]. 连铸, 2022(5): 50. (ZHAO Xin-kai, TIAN Feng-xi, GAO Wen-juan, et al. Behavior analysis of non-metallic inclusion groups in bearing steel during bloom casting[J]. Continuous Casting, 2022(5): 50.)
[15] WANG X, LI X, HUANG F, et al. Control of stringer shaped non-metallic inclusions of CaO-Al₂O₃ system in API X80 linepipe steel plates[J]. Steel Research International, 2014, 85(2):155.
[16] YANG D, WANG X, YANG G, et al. Inclusion evolution and estimation during secondary refining in calcium treated aluminum killed steels[J]. Steel Research International, 2014, 85(11):1517.
[17] YANG W, CAO J, WANG X, et al. Investigation on non-metallic inclusions in LCAK steel produced by BOF-LF-FTSC production route[J]. Journal of Iron and Steel Research International, 2011, 18(9): 6.
[18] YANG J, WANG X, JIANG M, et al. Effect of calcium treatment on non-metallic inclusions in ultra-low oxygen steel refined by high basicity high Al₂O₃ slag[J]. Journal of Iron and Steel Research International, 2011, 18(7): 8.
[19] 杨光维, 郝鑫, 杨叠,等. GCr15轴承钢冶炼过程钢液洁净度变化[J]. 钢铁, 2014, 49(11): 31. (YANG Guang-wei, HAO Xin, YANG Die, et al. Cleanliness of GCr15 bearing steel during steelmaking process[J]. Iron and Steel, 2014, 49(11): 31.)
[20] 耿鑫, 宋波, 刘涛, 等. 38CrMoAl钢精炼过程夹杂物生成及演变规律[J]. 中国冶金, 2022, 32(11): 106. (GENG Xin, SONG Bo, LIU Tao, et al. Inclusion generation and evolution of 38CrMoAl steel in refining process[J]. China Metallurgy, 2022, 32(11): 106.)
[21] 王康, 刘剑辉, 杨树峰, 等. GCr15 轴承钢 EAF-LF-VD-CC 流程非金属夹杂物的演变[J]. 钢铁, 2020, 55(2): 48. (WANG Kang, LIU Jian-hui, YANG Shu-feng, et al. Evolution of non-metallic inclusions in EAF-LV-VD-CC process of GCr15 bearing steel[J]. Iron and Steel, 2020, 55(2):48.)
[22] 王章印, 姜敏, 王新华. Q345D 钢精炼过程夹杂物生成及演变行为[J]. 钢铁, 2022, 57(2): 63. (WANG Zhang-yin, JIANG Min, WANG Xin-hua. Formation and evolution of inclusions in Q345D steel during secondary refining process[J]. Iron and Steel, 2022, 57(2): 63.)
[23] 王强, 朱航宇, 孙剑, 等. SWRCH45K冷镦钢非金属夹杂物生成及演变行为[J]. 中国冶金, 2020, 30(11): 41. (WANG Qiang, ZHU Hang-yu, SUN Jian, et al. Formation and evolution behavior of non-metallic inclusions in SWRCH45K cold heading steel[J]. China Metallurgy, 2020, 30(11): 41.)
[24] Todoroki H, Mizuno K. Effect of silica in slag on inclusion compositions in 304 Stainless steel deoxidized with aluminum[J]. ISIJ International, 2004, 44(8):1350.
[25] Matsumoto T, Watanabe Y, Yamauchi T. Recent development to decrease spinel-type inclusions by modification of slag composition at ladle furnace[C]//AISTech 2018 Conference Proceedings. Philadelphia: Association for Iron and Steel Technology, 2018: 1273.
[26] WEN B, SONG B, PAN N, et al. Effect of SiMg alloy on inclusions and microstructures of 16Mn steel[J]. Ironmaking and Steelmaking, 2011, 38(8): 577.
[27] LIU C, HUANG F, SUO J, et al. Effect of magnesia-carbon refractory on the kinetics of MgO·Al₂O₃ spinel inclusion generation in extra-low oxygen steels[J]. Metallurgical and Materials Transactions B, 2016, 47(2): 989.
[28] LIU C Y, YAGI M, GAO X, et al. Dissolution behavior of Mg from magnesia-chromite refractory into Al-killed molten steel[J]. Metallurgical and Materials Transactions B, 2018, 49(5): 2298.
[29] LIU C Y, YAGI M, GAO X, et al. Kinetics of transformation of Al₂O₃ to MgO·Al₂O₃ spinel inclusions in Mg-containing steel[J]. Metallurgical and Materials Transactions B, 2018, 49(1): 113.
[30] LIU C, HUANG F, WANG X. The effect of refining slag and refractory on inclusion transformation in extra low oxygen steels[J]. Metallurgical and Materials Transactions B, 2016, 47(2): 999.
[31] 王新华, 姜敏, 于会香, 等. 超低氧特殊钢中非金属夹杂物研究[J]. 炼钢, 2015, 31(6): 1. (WANG Xin-hua, JIANG Min, YU Hui-xiang, et al. Investigation on non-metallic inclusions in ultra-low oxygen special steels[J]. Steelmaking, 2015, 31(6): 1.)
[32] 周力, 马建超, 刘从德, 等. 二次氧化及钙处理对超低氧特殊钢中非金属夹杂物的影响[J]. 炼钢, 2017, 33(5): 66. (ZHOU Li, MA Jian-chao, LIU Cong-de, et al. Influence of reoxidation and calcium treatment on nonmetallic inclusions in ultra-low oxygen special steel[J]. Steelmaking, 2017, 33(5): 66.)
[33] Sasai K, Mizukami Y. Effect of stirring on oxidation rate of molten steel[J]. ISIJ International, 1996, 36(4): 388.
[34] Sasai K, Mizukami Y. Effects of tundish cover powder and teeming stream on oxidation rate of molten steel in tundish[J]. ISIJ International, 1998, 38(4): 332.