Cross shear deformation mechanism of stainless steel/carbon steel clad plate in longitudinal corrugated rolling
LI Yaxin1, LIU Yuanming1,2,3, WANG Zhenhua1,2,3, ZHANG Mingze1, ZHANG Bowen1, WANG Tao1,2,3
1. College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan 030024, Shanxi, China; 2. Engineering Research Center of Advanced Metal Composites Forming Technology and Equipment, Taiyuan University of Technology, Taiyuan 030024, Shanxi, China; 3. National Key Laboratory of Metal Forming Technology and Heavy Equipment, Taiyuan University of Technology, Taiyuan 030024, Shanxi, China
Abstract：Stainless steel/carbon steel clad plate not only possesses the strong corrosion resistance, high wear resistance, high heat resistance and high magnetism of stainless steel, but also combines the easy weldability, high thermal conductivity and easy ductility of carbon steel. However, the low bonding strength of stainless steel/carbon steel clad plate severely limits its wide application. In this paper, the technology of preparing stainless steel/carbon steel clad plate by longitudinal corrugated rolling (LCR) is presented. The effect of cross shear zone on bonding strength of clad plate is studied in deformation zone by experiment and finite element model (FEM) compared with flat rolling (FR) process. The results show that the tensile shear strengths of LCR clad plate at the peak and trough are 315.94 MPa and 329.48 MPa, respectively, and that of FR clad plate is 277.77 MPa. The tensile shear strengths of the peak and trough are 13.7% and 18.6% higher than that of FR clad plate, respectively. Through the element scanning analysis of the tensile shear fracture surface, the results show that the fracture position of the peak and trough of LCR clad plate is at the Q235B matrix, and the fracture position of FR clad plate is at the bonding interface. The tensile strength and elongation of LCR clad plate are better than FR clad plate. The stress state distributions of LCR and FR clad plates are obtained by FEM. Some metals are in the state of two compressive stresses and one tensile stress in the LCR deformation zone, and the stress state is closer to the pure shear state. The LCR clad plate is subjected to the action of tensile stress and strong shear stress in the rolling process. Different from FR deformation zone, there are cross shear zones in rolling and transverse directions due to the influence of corrugation roll shape in the LCR deformation zone. The existence of cross shear zones can enhance the shear effect between dissimilar metals, which is conducive to the cracking of the oxidized and hardened layers, promotes the combination of clad plate, and improves the bonding strength of the clad plate.
[1] LIU Y M, WANG Z H, WANG T, et al. Prediction and analysis of the force and shape parameters in variable gauge rolling[J]. Chinese Journal of Mechanical Engineering, 2022, 35(4): 79. [2] 王振华, 刘元铭, 王涛, 等. 粗轧过程中轧制力和宽展的预测与分析[J].钢铁, 2022, 57(9): 95.(WANG Z H, LIU Y M, WANG T, et al. Prediction and analysis of rolling force and width spread in rough rolling[J]. Iron and Steel, 2022, 57(9): 95.) [3] 宜亚丽, 韩晓铠, 金贺荣. 带夹层不锈钢复合板异步轧制力数学模型研究[J]. 钢铁, 2020, 55(9): 69.(YI Y L, HAN X K, JIN H R. Research on mathematical model of asymmetric rolling force of sandwich clad plate[J]. Iron and Steel, 2020, 55(9): 69.) [4] JI C, HUANG H, MENG K. Influence of process layouts of multi-roll solid-liquid cast-rolling bonding process on circumferential performance uniformity during fabricating metal cladding materials[J]. Journal of Materials Processing Technology, 2022, 301: 117444. [5] YU W D, JING Y A, HE X Z, et al. An innovative process of clad teeming and rolling for preparing stainless steel/carbon steel clad plate[J]. Journal of Manufacturing Processes, 2022, 84: 1428. [6] LIU B X, YIN F X, DAI X L, et al. The tensile behaviors and fracture characteristics of stainless steel clad plates with different interfacial status[J]. Materials Science and Engineering: A, 2017, 679: 172. [7] XUE J, BOUCHARD J, CHEN X, et al. Anisotropic elastic constants calculation of stainless steel cladded layers of pressure vessel steel plate[J]. International Journal of Pressure Vessels and Piping, 2019, 177: 103991. [8] 王小勇, 王卫华, 丁文华, 等. 不锈钢复合板热疲劳性能分析[J]. 中国冶金, 2022, 32(11): 73.(WANG X Y, WANG W H, DING W H,et al. Analysis on thermal fatigue properties of stainless steel clad plate[J]. China Metallurgy, 2022, 32(11): 73.) [9] 王伟聪, 杜华云, 侯利锋, 等. 新型奥氏体耐热不锈钢C-HRA-5的热变形行为[J].钢铁研究学报, 2022, 34(5): 496.(WANG W C, DU H Y, HOU L F, et al. Hot deformation behavior of C-HRA-5 new austenitic heat resistant stainless steel[J]. Journal of Iron and Steel Research, 2022, 34(5): 496.) [10] 李龙, 张心金, 刘会云, 等. 热轧不锈钢复合板界面剪切强度测定[J].钢铁, 2013, 48(12): 52.(LI L, ZHANG X J, LIU H Y, et al. Shear strength of the interface of hot rolled stainless clad steel[J]. Iron and Steel, 2013, 48(12): 52.) [11] 金贺荣, 周永强, 耿永祥, 等. 宽厚不锈钢复合板轧制力计算与参数影响分析[J].钢铁, 2015, 50(5): 38.(JIN H R, ZHOU Y Q, GENG Y X, et al. Rolling force calculation and parameters influence analysis of wide stainless steel clad plate[J]. Iron and Steel, 2015, 50(5): 38.) [12] LIU K, CHEN P, RAN C, et al. Investigation on the interfacial microstructure and mechanical properties of the W-Cu joints fabricated by hot explosive welding[J]. Journal of Materials Processing Technology, 2022, 300: 117400. [13] FU Y, GUO N, ZHOU C, et al. Investigation on in-situ laser cladding coating of the 304 stainless steel in water environment[J]. Journal of Materials Processing Technology, 2021, 289: 116949. [14] WU Y, WANG T, REN Z, et al. Evolution mechanism of microstructure and bond strength based on interface diffusion and IMCs of Ti/steel clad plates fabricated by double-layered hot rolling[J]. Journal of Materials Processing Technology, 2022, 310: 117780. [15] ZHANG B Y, LIU B X, HE J N, et al. Microstructure and mechanical properties of SUS304/Q235 multilayer steels fabricated by roll bonding and annealing[J]. Materials Science and Engineering: A, 2019, 740/741: 92. [16] FU L, XIAO H, YU C, et al. Bonding enhancement of cold rolling Al/steel composite plates via self-nano film modification[J]. Journal of Materials Processing Technology, 2022, 300: 117427. [17] YU T, JING Y A, YAN X L, et al. Microstructures and properties of roll-bonded stainless /medium carbon steel clad plates[J]. Journal of Materials Processing Technology, 2019, 266: 264. [18] 骆宗安, 杨德翰, 谢广明, 等. 真空制坯热轧钛/钢复合板工艺及性能[J].钢铁研究学报, 2019, 31(2): 213.(LUO Z A, YANG D H, XIE G M, et al. Production process and performance of titanium-steel vacuum roll-cladding plates[J]. Journal of Iron and Steel Research, 2019, 31(2): 213.) [19] 于涛, 井玉安, 张亚樵, 等. 不锈钢复合板界面组织形貌[J].钢铁, 2018, 53(11): 63.(YU T, JING Y A, ZHANG Y Q, et al. Interfacial microstructure morphologies of stainless steel clad plate[J]. Iron and Steel, 2018, 53(11): 63.) [20] 赵云鹏, 余超, 肖宏, 等. 纯铁中间层对热轧不锈钢复合板性能的影响[J].钢铁, 2020, 55(5): 73.(ZHAO Y P, YU C, XIAO H, et al. Effect of pure iron interlayer on mechanical properties of hot rolled stainless steel clad plate[J]. Iron and Steel, 2020, 55(5): 73.) [21] 雷冬, 任勇, 程晓茹, 等. 热处理对316L/Q235复合板组织与力学性能的影响[J].钢铁, 2017, 52(5): 66.(LEI D, REN Y, CHENG X R, et al. Effect of heat treatment on microstructure and mechanical properties of 316L/Q235 stainless steel composite panel[J]. Iron and Steel, 2017, 52(5): 66.) [22] 郭雄伟,武张静,李宁,等. 钛/钢层合板轧制复合研究进展与展望[J]. 中国冶金, 2021, 31(3): 1.(GUO X W, WU Z J, LI N, et al. Research progress and prospects of rolling titanium/steel laminates[J]. China Metallurgy, 2021, 31(3): 1.) [23] 龚闯伟,程晓茹,张尧,等.轧制工艺对复合钢板组织的影响[J].上海金属,2015,37(1):5.(GONG C W,CHENG X R,ZHANG Y, et al. Effect of rolling process on microstructure of the clad plates[J]. Shanghai Metals,2015,37(1):5.) [24] 刘强,柴希阳,柴锋,等. 回火热处理对轧制钛/钢复合板界面组织与性能的影响[J]. 中国冶金, 2019, 29(10): 44.(LIU Q,CHAI X Y,CHAI F,et al. Effect of tempering heat treatment on interface microstructure and mechanical properties of hot-rolled titanium clad steel plates[J]. China Metallurgy, 2019, 29(10): 44.) [25] 孙浩,王克鲁.不锈钢复合板生产方法和制备技术的探讨[J].上海金属,2005(1):50. (SUN H, WANG K L. Discussion on the production method and manufacturing technology of clad plate of stainless steel[J]. Shanghai Metals, 2005(1):50.) [26] WANG T, LI S, NIU H, et al. EBSD research on the interfacial microstructure of the corrugated Mg/Al laminated material[J]. Journal of Materials Research and Technology, 2020, 9(3): 5840. [27] WANG T, LI S, REN Z, et al. A novel approach for preparing Cu/Al laminated composite based on corrugated roll[J]. Materials Letters, 2019, 234: 79. [28] WANG T, WANG Y, BIAN L, et al. Microstructural evolution and mechanical behavior of Mg/Al laminated composite sheet by novel corrugated rolling and flat rolling[J]. Materials Science and Engineering: A, 2019, 765: 138318. [29] 和东平, 徐慧东, 王涛, 等. 基于动态轧制力的波纹辊轧机非线性振动[J].钢铁, 2021, 56(6): 75.(HE D P, XU H D, WANG T, et al. Nonlinear vibration of corrugated rolling mill based on dynamic rolling force[J]. Iron and Steel, 2021, 56(6): 75.) [30] LI X, ZU G, DING M, et al. Interfacial microstructure and mechanical properties of Cu/Al clad sheet fabricated by asymmetrical roll bonding and annealing[J]. Materials Science and Engineering: A, 2011, 529: 485. [31] LIU Y X, LIU Y M, WANG Z H, et al. Stress analysis and microstructure evolution of the Cu/Al composite plate during corrugated rolling[J]. Transactions of Nonferrous Metals Society of China, 2023,33(5):1460. [32] WANG T, LIU W, LIU Y, et al. Formation mechanism of dynamic multi-neutral points and cross shear zones in corrugated rolling of Cu/Al laminated composite[J]. Journal of Materials Processing Technology, 2021, 295: 117157. [33] 刘旭明, 冯光宏, 刘鑫, 等. 不锈钢-碳钢复合带肋钢筋的制备工艺研究[J].钢铁研究学报, 2021, 33(2): 149.(LIU X M, FENG G H, LIU X, et al. Research on manufacturing process of stainless steel/carbon steel composite rebar[J]. Journal of Iron and Steel Research, 2021, 33(2): 149.) [34] 邵春娟, 镇凡, 陆春洁, 等. 热轧S31603/Q370q不锈钢复合板界面特征分析[J].钢铁研究学报, 2022, 34(2): 181.(SHAO C J, ZHEN F, LU C J, et al. Analysis on interface characteristics of hot-rolled S31603/Q370q stainless clad steel plate[J]. Journal of Iron and Steel Research, 2022, 34(2):181.) [35] WANG S, LIU B X, CHEN C X, et al. Microstructure, mechanical properties and interface bonding mechanism of hot-rolled stainless steel clad plates at different rolling reduction ratios[J]. Journal of Alloys and Compounds, 2018, 766:517. [36] CHEN C X, LIU M Y, LIU B X, et al. Tensile shear sample design and interfacial shear strength of stainless steel clad plate[J]. Fusion Engineering and Design, 2017, 125: 431. [37] 黄乐庆, 程晓茹, 龚闯伟, 等. 中间材Ni对轧制碳钢-不锈钢复合界面的影响[J]. 上海金属, 2016, 38(2): 1.(HUANG L Q, CHENG X R, GONG C W, et al. Effect of interlayer Ni on clad interface of rolling carbon steel/stainless steel[J].Shanghai Metals, 2016, 38(2): 1.) [38] BAI Y, WIERZBICKI T. A new model of metal plasticity and fracture with pressure and Lode dependence[J]. International Journal of Plasticity, 2008, 24(6): 1071. [39] WANG Z. Physical essence of lode parameter and its effect on plastic flow[J]. Acta Mechanica Solida Sinica, 2006, 27(3): 277.
2023, Vol. 58 
